Some EcoNet based routers ship an on-flash EEPROM whose chip-id is
0x7592 instead of the expected 0x7603. The device probes as PCI
14c3:7603 and the hardware MT_HW_CHIPID register reports 0x7603,
independent of the EEPROM value.
This is seen across multiple EcoNet EN751221 and EN7528 based devices
(for example the Genexis Platinum 4410).
Signed-off-by: Ahmed Naseef <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
The SKB containing the generated beacon is not freed when the beacon
queue is deected stuck and scheduled for recovery.
Fixes potential memory leaks in case the beacon queue is detected stuck.
Signed-off-by: David Bauer <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Currently, per-radio attributes are set on per-phy basis, i.e., all the
radios present in a wiphy will take attributes values sent from user. But
each radio in a wiphy can get different values from userspace based on
its requirement.
To extend support to set per-radio attributes, add support to get radio
index from userspace. Add an NL attribute - NL80211_ATTR_WIPHY_RADIO_INDEX,
to get user specified radio index for which attributes should be changed.
Pass this to individual drivers, so that the drivers can use this radio
index to change per-radio attributes when necessary. Currently, per-radio
attributes identified are:
NL80211_ATTR_WIPHY_TX_POWER_LEVEL
NL80211_ATTR_WIPHY_ANTENNA_TX
NL80211_ATTR_WIPHY_ANTENNA_RX
NL80211_ATTR_WIPHY_RETRY_SHORT
NL80211_ATTR_WIPHY_RETRY_LONG
NL80211_ATTR_WIPHY_FRAG_THRESHOLD
NL80211_ATTR_WIPHY_RTS_THRESHOLD
NL80211_ATTR_WIPHY_COVERAGE_CLASS
NL80211_ATTR_TXQ_LIMIT
NL80211_ATTR_TXQ_MEMORY_LIMIT
NL80211_ATTR_TXQ_QUANTUM
By default, the radio index is set to -1. This means the attribute should
be treated as a global configuration. If the user has not specified any
index, then the radio index passed to individual drivers would be -1. This
would indicate that the attribute applies to all radios in that wiphy.
Signed-off-by: Roopni Devanathan <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Johannes Berg <[email protected]>
MediaTek has asked to switch from the ISC license to BSD-3-Clause-Clear,
in order to improve clarity and the legal integrity of the code.
The BSD-3-Clause license includes the "no endorsement" clause, which is
important for protecting the reputation of the original authors and
contributors by preventing unauthorized use of their names for endorsement
purposes.
This clause is absent in the BSD-2-Clause license, which is more permissive
but lacks this specific protection.
This change also cleans up the license of some Kconfig/Makefile files,
which were accidentally marked as GPL.
The GPL 2.0 remains in use on mt76x0, as well as two source files in mt7615
for which the license situation still needs to be clarified.
Signed-off-by: Felix Fietkau <[email protected]>
mt76_eeprom_override has of_get_mac_address, which can return
-EPROBE_DEFER if the nvmem driver gets loaded after mt76 for some
reason.
Make sure this gets passed to probe so that nvmem mac overrides always
work.
Signed-off-by: Rosen Penev <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Embedding net_device into structures prohibits the usage of flexible
arrays in the net_device structure. For more details, see the discussion
at [1].
Un-embed the net_devices from struct mt76_dev by converting them
into pointers, and allocating them dynamically. Use the leverage
alloc_netdev_dummy() to allocate the net_device object at
mt76_dma_init().
The free of the device occurs at mt76_dma_cleanup().
Link: https://lore.kernel.org/all/[email protected]/ [1]
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: Breno Leitao <[email protected]>
Acked-by: Kalle Valo <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
In mt76_wmac_probe(), when the mt76_alloc_device() call succeeds, memory
is allocated for both struct ieee80211_hw and a workqueue. However, on
the error path, the workqueue is not freed. Fix that by calling
mt76_free_device() on the error path.
Fixes: c8846e101502 ("mt76: add driver for MT7603E and MT7628/7688")
Signed-off-by: Abdun Nihaal <[email protected]>
Reviewed-by: Jiri Slaby <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Several places use rcu_dereference to get a wcid entry without validating
if the index exceeds the array boundary. Fix this by using a helper function,
which handles validation.
Signed-off-by: Felix Fietkau <[email protected]>
mt76 does a lot of:
local_bh_disable();
napi_enable(...napi);
napi_schedule(...napi);
local_bh_enable();
local_bh_disable() is not a real lock, its most likely taken
because napi_schedule() requires that we invoke softirqs at
some point. napi_enable() needs to take a mutex, so move it
from under the BH protection.
Fixes: 413f0271f396 ("net: protect NAPI enablement with netdev_lock()")
Reported-by: Dan Carpenter <[email protected]>
Link: https://lore.kernel.org/[email protected]
Reviewed-by: Eric Dumazet <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
Fixes linked list management issues during restart, where sta entries
can be recreated and reinitialized while still in the poll list, triggering
kernel warnings.
Signed-off-by: Felix Fietkau <[email protected]>
Also report auth/disassoc events, in order to give the driver more control over
handling the station state.
Signed-off-by: Felix Fietkau <[email protected]>
This allows the core code to change the channel. Code deduplication and
preparation for adding scanning code to the core.
Signed-off-by: Felix Fietkau <[email protected]>
Move the qid variable declaration further up
Fixes: b473c0e47f04 ("wifi: mt76: mt7603: fix tx queue of loopback packets")
Signed-off-by: Felix Fietkau <[email protected]>
This flag is needed for the PSE client reset. Fixes watchdog reset issues.
Fixes: c677dda16523 ("wifi: mt76: mt7603: improve watchdog reset reliablity")
Signed-off-by: Felix Fietkau <[email protected]>
Use the correct WMM AC queue instead of the MGMT one to fix potential issues
with aggregation sequence number tracking. Drop non-bufferable packets.
Fixes: fca9615f1a43 ("mt76: mt7603: fix up hardware queue index for PS filtered packets")
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mtk_wed_device pointer in mt76_queue structure in order to
configure WED chip.
Get rid of dev parameter in Q_READ and Q_WRITE macros.
Introduce wed parameter to the following routine signatures:
- mt76_init_queue
- mt76_init_tx_queue
This is a preliminary patch to introduce WED support for mt7996 since
mt7996 runs two separate WED chips.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Before preparing the new beacon, check the queue status, flush out all
previous beacons and buffered multicast packets, then (if necessary)
try to recover more gracefully from a stuck beacon condition by making a
less invasive attempt at getting the MAC un-stuck.
Fixes: c8846e101502 ("mt76: add driver for MT7603E and MT7628/7688")
Signed-off-by: Felix Fietkau <[email protected]>
Only trigger PSE reset if PSE was stuck, otherwise it can cause DMA issues.
Trigger the PSE reset while DMA is fully stopped in order to improve
reliabilty.
Fixes: c8846e101502 ("mt76: add driver for MT7603E and MT7628/7688")
Signed-off-by: Felix Fietkau <[email protected]>
It turns out that the code in mt7603_rx_pse_busy() does not detect actual
hardware hangs, it only checks for busy conditions in PSE.
A reset should only be performed if these conditions are true and if there
is no rx activity as well.
Reset the counter whenever a rx interrupt occurs. In order to also deal with
a fully loaded CPU that leaves interrupts disabled with continuous NAPI
polling, also check for pending rx interrupts in the function itself.
Fixes: c8846e101502 ("mt76: add driver for MT7603E and MT7628/7688")
Signed-off-by: Felix Fietkau <[email protected]>
Setting MT_TX_ABORT does not abort any transmission for a wtbl index on its
own. Instead, it modifies the behavior of a queue flush to make it selectively
flush packets for a particular wtbl index.
Adjust powersave filtering to make use of this in order to avoid running into
unnecessary timeouts while flushing
Signed-off-by: Felix Fietkau <[email protected]>
When disabling beacons on a vif, intval is 0. Ensure that dev->mt76.beacon_int
is not overwritten in this case, so that beacons continue to work for other
interfaces.
Signed-off-by: Felix Fietkau <[email protected]>
Rely on poll_list field in mt76_wcid structure and get rid of
private copy.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rely on sta_poll_list and sta_poll_lock fields in mt76_dev structure
and get rid of private copies.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
According to the documentation, ieee80211_rx_list must not run concurrently
with ieee80211_tx_status (or its variants).
Cc: [email protected]
Fixes: 88046b2c9f6d ("mt76: add support for reporting tx status with skb")
Reported-by: Brian Coverstone <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This helps avoid cleartext leakage of already queued or powersave buffered
packets, when a reassoc triggers the key deletion.
Cc: [email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Run mt7603_mcu_restart routine directly and avoid mcu_restart function
pointer whenever it is possible.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move leds struct in mt76_phy in order to have leds associated to phy
(e.g. in dbdc mode) instead of per device.
Tested-by: Frank Wunderlich <[email protected]>
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move aggregation stats array per-phy instead of share it between multiple
interfaces. This is a preliminary patch to add mt7996 driver support.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
MT7915_MAX_INTERFACES is per-band declaration in MT7915/MT7986/MT7916.
Enlarge vif_mask to 64 bits wide, including the bit operation.
Reviewed-by: Shayne Chen <[email protected]>
Signed-off-by: Evelyn Tsai <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Switch to use le32/16_get_bits() to simplfy codes and specify
the size explicitly to avoid potential issues.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Instead of just taking the maximum per-chain signal strength values,
add an approximation for the sum of the combined signal.
This should more accurately reflect the real signal strength, especially
if the per-chain signal strength values are close to each other
Signed-off-by: Felix Fietkau <[email protected]>
Check sta_rates pointer value in mt7603_sta_rate_tbl_update routine
since minstrel_ht_update_rates can fail allocating rates array.
Fixes: c8846e1015022 ("mt76: add driver for MT7603E and MT7628/7688")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Leave more time to abort transmissions (which could happen at low CCK rates)
Only warn if the last filter command is stuck
Signed-off-by: Felix Fietkau <[email protected]>
