Queue frames pushed by mac80211 running mt7615_tx if the device is
low-power state. Run wake workqueue in order to swicth to full-power
before transmitting pending frames
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Make sure the device is in full-power before pulling frames from
mac80211 queues
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7615_update_survey utility routine in order to compute
survey stats without waking up the device since it runs holding mt76 lock.
Run mt7615_pm_wake directly in mt7615_update_channel since it can run
with mt76.mutex held if called by mac80211
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce runtime-pm power_save delayed work used to enable
low-power after an inactivity period
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7615_mutex_{acquire,release} utility routines in order to
switch in full-power/low-power before/after accessing device register-map
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7615_pm_wake utility routine to wake the device from
runtime low-power state (lower-power state is currently supported by
offload firmware for pcie devices).
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76 workqueue from usb to common code in order to be reused adding
low-power support for mt7663 chipset
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Supports sending a configurable number of packets with a specific rate
and configurable tx power levels / antenna settings, as well as displaying
rx statistics.
Signed-off-by: Felix Fietkau <[email protected]>
Unlike on earlier chips, DMA completion on MT7615 does not imply actually
having sent out any packets.
Since AQL will prevent filling the hardware queues and will only allow more
packets to be passed to the driver after tx completion, it makes much more
sense to schedule the tx tasklet there.
This is also needed for scheduling tx in testmode support
Signed-off-by: Felix Fietkau <[email protected]>
Overwrite hw queue id for non-bufferable management frames if the hw
support always txq (altxq) in order to be in sync with mac txwi code
Fixes: cdad4874057d ("mt76: mt7615: add dma and tx queue initialization for MT7622")
Fixes: f40ac0f3d3c0 ("mt76: mt7615: introduce mt7663e support")
Suggested-by: Felix Fietkau <[email protected]>
Tested-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce remain_on_channel support to mt7615 driver if the device is
running offload firmware
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
All drivers before MT7915 have a limit of 128 WCID entries. Stop relying
on ARRAY_SIZE(dev->mt76.wcid), since it no longer reflects that limit.
Fixes: 49e649c3e0a6 ("mt76: adjust wcid size to support new 802.11ax generation")
Reported-by: kbuild test robot <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Since usb code can't access device registers in interrupt context, move
rcu_read_lock/rcu_read_unlock in mt7615_poll_tx routine. Moreover loop
over a local msta list in mt7615_mac_sta_poll since mt7663u driver will
not be able to complete the inner while loop before sta_poll_list list
is refilled by mt7615_mac_add_txs/mt7615_mac_fill_rx
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
A switch from one rate index to the next only happens when tx count from
the current slot is greater than MT7615_RATE_RETRY, which is 1 has to be
subtracted from count, instead of added to it.
Signed-off-by: Felix Fietkau <[email protected]>
Sometimes mt7615_mac_set_timing gets called while the slot time is still
configured to 20. Ensure that in this case it always uses the OFDM CFend
rate.
Signed-off-by: Felix Fietkau <[email protected]>
Add missing register definitions in order to enable sensitivity tuning
for mt7663 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce support for mt7663u 802.11ac 2x2:2 chipset to mt7615 driver.
Main difference respect to pcie code base is the usb code needs to
configure wtbl from non-atomic context
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Create mt7615-common module in order to collect shared code between usb
and mmio code. Move the following source files in mt7615-common module:
- main.c
- init.c
- mcu.c
- mac.c
- debugfs.c
- eeprom.c
- trace.c
Create the following source files for mmio only source code and move them
in mt7615e module:
- pci_init.c
- dma.c
- pci_mac.c
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
make mac_work per phy instead of per device and fix a possible deadlock
in mt7615_stop since mt7615_mac_work runs holding mt76 mutex
Fixes: fdd2e570764c2 ("mt76: mt7615: add dual-phy support for mac80211 ops")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix DMA unmap length estimation in mt7615_txp_skb_unmap_hw for mt7622
chipset
Fixes: 6aa4ed7927f1 ("mt76: mt7615: implement DMA support for MT7622")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Check that val is not zero before aggr_per estimation in order to avoid a
possible division by 0
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Generalize mt7615_rate_desc introducing mt7615_wtbl_desc and
mt7615_key_desc data structures in order to configure the hw wtbl
in a non-atomic context for usb devices
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove key dependency from mt7615_mac_wtbl_update_key and export
mt7615_mac_wtbl_update_key, mt7615_mac_wtbl_update_pk and
mt7615_mac_wtbl_update_cipher in order to reuse them in usb code.
Move mt7615_mac_get_cipher in mac.h
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt7615_mac_wtbl_addr in mac.h and add inline qualifier in order to
be reused adding usb support to mt7615 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move register configuration out of mt7615_mac_set_rates since usb
driver can't access device register in interrupt context. Introduce
mt7615_mac_update_rate_desc routine to report rate info to
mt7615_mac_set_rates
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Disable dfs RDD mcu commands for mt7663 driver since they are not
currently supported by the 7663 firmware
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Make scs configurable per phy since most of the chipsets do not
support dbdc
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Simplify mib macros and use proper type for related counters.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In order to reuse mt7615 code adding support for mt7663e driver,
introduce mt7615e_reg_map since mt7663e and mt7615 rely on a
different base registers definitions.
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt7615_mcu_set_beacon_offload, mt7615_mcu_set_dev and
mt7615_mcu_set_bss routine in mt7615_mcu_ops data structure.
This is a preliminary patch to support mt7663 firmware
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This if statement was supposed to be deleted, but it wasn't. It means
that we sometimes don't set the sensitivity correctly.
Fixes: 2cad515ece8a ("mt76: mt7615: add missing settings for simultaneous dual-band support")
Signed-off-by: Dan Carpenter <[email protected]>
When injecting beacon frames via monitor interface, they must not be sent to
the beacon hardware queue, because they don't follow normal hardware beacon tx
rules.
Fix sending them by adding a flag to mt7615_mac_write_txwi that selects the
beacon queue for tx, and use it only from mt7615_mcu_set_bcn.
Signed-off-by: Felix Fietkau <[email protected]>
