The Group ID Management frame is an Action frame of category VHT.
It is transmitted by the AP to assign or change the user position
of a STA for one or more group IDs.
Also, sniffer can use a given group id to monitor STA that belongs
to that group.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
gen_ppe_thresh routine is shared between mt7615, mt7915, mt7921 and
mt7996 so move it in mt76_connac module.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
irq_tasklet struct is used by most of the drivers (e.g. mt7915, mt7921,
mt7615, mt7663 and mt7996) so move it in common code.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The connac3 removes fixed rate fields to reduce txd size and introduces
global rate tables (64 entries) for rate setting. Driver needs to fill
the corresponding idx in MT_TXD6_TX_RATE while tx, and push mt76_rate
into predifined table at bootup stage so that mvif->basic_rates_idx
can immediately switch out once setting changes.
spe_idx is also needed for fixed rate frames, and will be updated by
future patches.
Note that all table entries are shared across driver and firmware
(i.e.TxBF), hence adding MT7996_BASIC_RATES_TBL to reflect mapping
status.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Host triggered and catastrophic event triggered firmware core dumping
for basic firmware issues triage, including state reporting, function
calltrace and MCU memory dump.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add mt7996_reset() and refactor mt7996_mac_reset_work() to support
full system recovery.
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Init mpdu density based on the hardware capability to prevent rx drop.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rework and extract common code of capability init for the preparation of
adding EHT capability.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add helpers to get the maximum wtbl size and interface num based
on hw caps.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use the sts variable when setting vht beamform sts cap.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move leds struct in mt76_phy in order to have leds associated to phy
(e.g. in dbdc mode) instead of per device.
Tested-by: Frank Wunderlich <[email protected]>
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This reports signal strength of ACK packets from the peer as measured
at each interface.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
