MediaTek has asked to switch from the ISC license to BSD-3-Clause-Clear,
in order to improve clarity and the legal integrity of the code.
The BSD-3-Clause license includes the "no endorsement" clause, which is
important for protecting the reputation of the original authors and
contributors by preventing unauthorized use of their names for endorsement
purposes.
This clause is absent in the BSD-2-Clause license, which is more permissive
but lacks this specific protection.
This change also cleans up the license of some Kconfig/Makefile files,
which were accidentally marked as GPL.
The GPL 2.0 remains in use on mt76x0, as well as two source files in mt7615
for which the license situation still needs to be clarified.
Signed-off-by: Felix Fietkau <[email protected]>
- remove stbc, because mt76x0 doesn't support it and mt76x2 uses the same
values as HT/VHT
- reduce vht array to 2 elements, because VHT MCS0-7 are the same as HT
Signed-off-by: Felix Fietkau <[email protected]>
No functional change intended.
Add SPDX identifiers to all remaining files in /mt76.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When loading EEPROM data from flash, the RF frontend settings need to be
initialized from flash data. Without this, the chip loads the wrong values
from its internal eFuse ROM.
Signed-off-by: Felix Fietkau <[email protected]>
Run mt76x0 tssi calibration process if enabled in eeprom data.
Perform calibration procedure every 4s
Signed-off-by: Lorenzo Bianconi <[email protected]>
Move mt76x02_eeprom_copy utility routine in mt76x02-lib module
in order to be reused by mt76x0 driver adding tssi calibration
support
Signed-off-by: Lorenzo Bianconi <[email protected]>
Update mt76x0_phy_ant_select() to conform vendor driver, most notably
add dual antenna mode support, read configuration from EEPROM and
move ant select out of channel config to init phase. Plus small MT7630E
quirk for MT_CMB_CTRL register which vendor driver dedicated to this
chip do.
This make MT7630E workable with mt76x0e driver and do not cause any
problems on MT7610U for me.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Add mt76x0_tssi_enabled in order to check if tssi compensation
is enabled since mt76x0 condition differs from mt76x2 one.
Moreover move back mt76x02_temp_tx_alc_enabled and mt76x02_tssi_enabled
routines in mt76x2/eeprom.h since they are mt76x2 specific
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use mt76x02_dev data structure as reference in mt76x02_eeprom.c
instead of mt76_dev
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In order to unify eeprom parsing between mt76x0 and mt76x2 drivers,
remove eeprom pointer dependency from mt76x0_set_tx_power_per_rate.
Moreover use mt76_rate_power to store power vs rate calibration data.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76x02_rate_power_val and mt76x2_sign_extend_optional utility
routines in mt76x02_eeprom.h in order to reuse them in mt76x0 eeprom
parsing
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76x2_tssi_enabled and mt76x02_temp_tx_alc_enabled in
mt76x02_eeprom.h in order to be reused in mt76x0 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76x02_eeprom_parse_hw_cap utility routine in mt76x02-lib
module in order to be reused in mt76x0 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Unify frequency offset parsing with mt76x2 driver using
eeprom utility routines available in mt76x02-lib module
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Unify temperature offset parsing with mt76x2 driver using
eeprom utility routines available in mt76x02-lib module
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add mt76x02_get_rx_gain and mt76x02_get_lna_gain utility routines
for rx gain parsing. mt76x02_get_rx_gain and mt76x02_get_lna_gain
will be reused for eeprom parsing in mt76x0 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76x2_ext_pa_enabled utility routine in mt76x02_eeprom.c
and remove duplicated code. This is a preliminary patch to
unify eeprom code between mt76x2 and mt76x0 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76x2_efuse_read and mt76x2_get_efuse_data in mt76x02_eeprom.c
in order to be reused in mt76x0 driver for eeprom parsing
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76x2_eeprom_get utility routine in mt76x02_eeprom.h since
it will be used to parse mt76x0 eeprom in order to unify eeprom
support between mt76x2 and mt76x0 drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76x2 and mt76x0 common definitions in mt76x02_eeprom.h
and remove duplicated code
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
