Add support for an extra wiphy in mt76_set_channel and mt76_get_survey
This is preparation for supporting multiple wiphys per device to support the
concurrent dual-band feature of MT7615D
Signed-off-by: Felix Fietkau <[email protected]>
status.info could point to skb->cb, leading to a use-after-free after the tx
status has been reported to mac80211
Signed-off-by: Felix Fietkau <[email protected]>
Host time is used to calculate the channel active time on mt7603 and mt7615.
Use the same on mt76x02 and move the lock to core code to get rid of some
duplicated code.
Signed-off-by: Felix Fietkau <[email protected]>
Report total rx airtime for valid stations as BSS rx time in survey
mt7615 is left out for now, it will be supported later by reading
hardware counters instead of calculating airtime in software
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_channel_state() from mt76.h to mac80211.c
Preparation for updating channel state from more places in the drivers/core
Signed-off-by: Felix Fietkau <[email protected]>
Move aggr_stats array from mt76x02_dev to mt76_dev in order to be reused
adding aggregation stats for mt7603/mt7615 drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Unify mac_reset_counter routine and move it in mt76x02_lib module
since it is shared by all mt76x02 drivers (pci/usb)
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
No functional change intended.
Add SPDX identifiers to all remaining files in /mt76.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This fixes the following checkpatch warnings:
ERROR: code indent should use tabs where possible
CHECK: Alignment should match open parenthesis
CHECK: No space is necessary after a cast
CHECK: Please don't use multiple blank lines
CHECK: Avoid precedence issues in macro
WARNING: Statements should start on a tabstop
WARNING: Unnecessary space before function pointer arguments
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove enable parameter from mt76x02_edcca_init routine signature since
it is always true
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When the hardware falls back to lower rates for a transmit attempt, only the
first status report will show the number of retries correctly. The frames
that follow will report the correct final rate, but number of retries set to 0.
This can cause the rate control module to vastly underestimate the number of
retransmissions per rate.
To fix this, we need to keep track of the initial requested tx rate per packet
and pass it to the status information.
For frames with tx status requested, this is simple: use the rate configured
in info->control.rates[0] as reference.
For no-skb tx status information, we have to encode the requested tx rate in
the packet id (and make it possible to distinguish it from real packet ids).
To do that, reduce the packet id field size by one bit, and use that bit to
indicate packet id vs rate.
This change also improves reporting by filling the status rate array with
rates from first rate to final rate, taking the same steps as the hardware
fallback table. This matters in corner cases like MCS8 on HT, where the
fallback target is MCS0, not MCS7.
Signed-off-by: Felix Fietkau <[email protected]>
Move beacon_mask in mt76_dev data structure since it is used by
all drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mac_work delayed work in mt76_dev data structure since
it is used by all drivers and it will be reused adding mac work to
mt7615
Signed-off-by: Lorenzo Bianconi <[email protected]>
Move most of beaconing code into separate file and separate beacon
initialization for USB and MMIO as pre TBTT implementation for USB
will be different.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use a separate lock and spin_trylock to avoid disabling interrupts.
Should improve performance and latency
Signed-off-by: Felix Fietkau <[email protected]>
Remove mt76_queue dependency from tx_complete_skb function pointer and
rely on mt76_tx_qid instead. Remove flush from tx_complete_skb
signature. This is a preliminary patch to introduce mt76_sw_queue
support
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Full tx blocking (as opposed to CCA blocking) should only happen if there
is a continuous non-802.11 signal above the energy detect threshold.
Unfortunately the ED/CCA counter can't detect that, as it also counts 802.11
signals as busy.
Similar to the vendor code, implement a learning mode that waits until the AGC
gain has already been adjusted to the lowest value (due to false CCA events),
and the number of false CCA events still remains high, and the blocking
threshold is exceeded for more than 5 seconds.
Signed-off-by: Felix Fietkau <[email protected]>
It needs to be always enabled for 76x2 and conditionally enabled/disabled
for 76x0. Since mt76x2_mac_stop clears this bit, ensure that it is enabled
in mt76x02_edcca_init
Signed-off-by: Felix Fietkau <[email protected]>
When the timer is already running, there is no need to reset the counter,
because the drift will remain the same.
Signed-off-by: Felix Fietkau <[email protected]>
Block only when the busy time reaches 92%, as lower values can be reached with
heavy 802.11 traffic as well.
Signed-off-by: Felix Fietkau <[email protected]>
Based on system load and time needed by other calibration runs, the time
between dev->mac_work runs can vary quite a bit.
Calculate busy time based on the actual time difference in order to avoid
potentially over-estimating busy time, which could lead to unnecessary tx
blocking.
Signed-off-by: Felix Fietkau <[email protected]>
ED/CCA Tx blocking checks need to be run every 100 ms in order to avoid
triggering too late and keeping tx blocking on for too long
Signed-off-by: Felix Fietkau <[email protected]>
Software encrypted packets can be passed not just through the drv_tx callback,
but also through the intermediate tx queue.
In order to deal with that, move the override to mt76x02_mac_write_txwi and
also take care of filling in the per-packet rate information
Signed-off-by: Felix Fietkau <[email protected]>
Configure beaconing on USB devices without PS buffering support.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
BSSID is not strtirct related with beaconing (for example we can have
2 STA vifs) and more related with MAC address, so initaize BSSID when
setting MAC address.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Since ccmp_pn is u8 *, the second half needs to start at array index 4
instead of 0. Fixes a connection stall after a certain amount of traffic
Fixes: 23405236460b9 ("mt76: fix transmission of encrypted management frames")
Cc: [email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Set the per-chain signal value for chain 0 and simplify the code
(no need for a loop for just one extra chain)
Signed-off-by: Felix Fietkau <[email protected]>
Take into account device rx stream in mt76x02_mac_process_rate
in order to not report wrong number of rx spatial stream to mac80211.
The issue has been reported on mt76x0 device which is 1x1:1 however
the hw sometimes reports rx nss equal to 2
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
On MT76x2, the hardware does not report tx status in the FIFO register,
if the packet id is 0.
Change the allocation of packet IDs to use 0 for no-ack packets, 1 for
non-probing packets and 2-255 for packets with tx status requested.
Fixes rate control issues
Signed-off-by: Felix Fietkau <[email protected]>
Felix Fietkau