Move leds struct in mt76_phy in order to have leds associated to phy
(e.g. in dbdc mode) instead of per device.
Tested-by: Frank Wunderlich <[email protected]>
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt7663 efuse has 0x600 bytes instead of 0x400. Increase the size in order
to fix issues with incomplete calibration data
Signed-off-by: Felix Fietkau <[email protected]>
Add a chanctx parameter to mt76_connac_mcu_uni_add_bss signature to allow
the firmware binds the BSS into the specific channel context.
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move aggregation stats array per-phy instead of share it between multiple
interfaces. This is a preliminary patch to add mt7996 driver support.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to move aggr_stats array in mt76_phy
structure.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This adds selectable RTC/CTS enablement for each interface.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Checking the relevant rxd bits for the checksum information only indicates
if the checksum verification was performed by the hardware and doesn't show
actual checksum errors. Checksum errors are indicated in the info field of
the DMA descriptor. Fix packets erroneously marked as CHECKSUM_UNNECESSARY
by checking the extra bits as well.
Those bits are only passed to the driver for MMIO devices at the moment, so
limit checksum offload to those.
Fixes: 2122dfbfd0bd ("mt76: mt7615: add rx checksum offload support")
Fixes: 94244d2ea503 ("mt76: mt7915: add rx checksum offload support")
Fixes: 0e75732764e8 ("mt76: mt7921: enable rx csum offload")
Signed-off-by: Felix Fietkau <[email protected]>
When 802.3 decap offload is enabled, the hardware indicates header translation
failure, whenever either the LLC-SNAP header was not found, or a VLAN header
with an unregcognized tag is present.
In that case, the hardware inserts a 2-byte length fields after the MAC
addresses. For VLAN packets, this tag needs to be removed. However,
for 802.3 LLC packets, the length bytes should be preserved, since there
is no separate ethertype field in the data.
This fixes an issue where the length field was omitted for LLC frames, causing
them to be malformed after hardware decap.
Fixes: 1eeff0b4c1a6 ("mt76: mt7915: fix decap offload corner case with 4-addr VLAN frames")
Reported-by: Chad Monroe <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce rx_check callback support for mt7663s driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Similar to mt7921 driver, introduce mt7615_mutex_acquire/release in
mt7615_sta_set_decap_offload in order to avoid sending mcu commands
while the device is in low-power state.
Fixes: d4b98c63d7a77 ("mt76: mt7615: add support for rx decapsulation offload")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce rx_check callback support for mt7663u and mt7921u drivers.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The code was accidentally shifting register values down by tid % 32 instead of
(tid * field_size) % 32.
Signed-off-by: Felix Fietkau <[email protected]>
Report phy_indx in tx_info->hw_queue. This is a preliminary patch to add
newer chipset support
Co-developed-by: Bo Jiao <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Introduce phy_idx to mt76_wcid structure instead of ext_phy.
This is a preliminary patch to add newer chipset support.
Co-developed-by: Bo Jiao <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Introduce phys array in mt76_dev structure to reference mt76_phy
supported by the chipset. This is a preliminary patch to introduce
newer chipset support.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Introduce phy_idx mt76_rx_status instead of ext_idx. This is a
preliminary patch to add newer chipset support
Co-developed-by: Bo Jiao <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Move mt76_connac_init_tx_queues and mt76_connac_tx_cleanup routines
in mt76_connac module. This is a preliminary patch to add mt7990
chipset support.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Previously the code used skb_set_queue_mapping for management or non-bufferable
powersave frames that need to be sent to a different hardware queue.
This can confuse AQL, which expects the value to remain the same until the tx
status report.
The only place that currently uses the altered skb queue mapping is the txwi
write function. Change the code to pass the hardware queue id as a function
parameter instead.
Signed-off-by: Felix Fietkau <[email protected]>
For some reason, mt7615 reacts badly to repeatedly enabling/disabling the radar
detector without also switching the channel.
This results in very bad throughput on DFS channels, because
hw->conf.radar_enabled can get toggled a few times after CAC ends.
Fix this by always leaving the DFS detector enabled on DFS channels and instead
suppress unwanted detection events.
Fixes: 2c86f6752046 ("mt76: mt7615: fix/rewrite the dfs state handling logic")
Signed-off-by: Felix Fietkau <[email protected]>
Set EXTRA_INFO_NEW for the first time only to prevent adding the same
starec entry, otherwise the entry might be removed in fw.
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_connac2_mcu_fill_message routine in shared module in order to
reuse it for mt7921 and mt7915e drivers. This is a preliminary patch to
add mt7990 driver support.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt7615_txp_skb_unmap in shared code and reuse it in mt7915e and
mt7921e driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Now we can move mt76_connac_write_hw_txp routine in mt76-connac module
and reuse it in mt7921e and mt7615e driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Since now txp structures are in common code we can reuse
mt76_connac_tx_complete_skb routine in mt7921e, mt7915e and mt7615e
drivers.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_connac_tx_free structure in mt76_connac module since it is
shared by mt7615 and mt7921 drivers.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Since mt7615_txp_ptr is shared between mt7615 and mt7921 move it in
mt76_connac module.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Since mt76_connac_fw_txp struct is shared between mt7615e, mt7915e and
mt7921e, move it in mt76_connac module.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Do not update pm stats if mt7615_mcu_fw_pmctrl returns an error.
Fixes: abe912ae3cd42 ("mt76: mt7663: add awake and doze time accounting")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
According IEEE Std 802.11-2020, its definition is:
Indicates whether the STA is capable of interpreting the Extended NSS BW
Support subfield of the VHT Capabilities Information field.
Some APs, such as Xiaomi AX6000, would check this one for BW settings.
mt76 driver can get max BW capability only if the this field is confgured
properly.
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
napi_schedule() can call __raise_softirq_irqoff(), which can perform softirq
handling, so it must not be called in a pure process context with BH enabled.
Signed-off-by: Felix Fietkau <[email protected]>
MT7915_MAX_INTERFACES is per-band declaration in MT7915/MT7986/MT7916.
Enlarge vif_mask to 64 bits wide, including the bit operation.
Reviewed-by: Shayne Chen <[email protected]>
Signed-off-by: Evelyn Tsai <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
When setup monitor mode in DFS channel, mt76 send CH_SWITCH_DFS to
fw for channel config. This would cause rx performance bad while
monitoring frames. Settings CH_SWITCH_NORMAL in monitor mode would
get the same performance as normal channels.
Reviewed-by: Shayne Chen <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce __mt76u_init unitility routine and move mt7615 usb bus ops
into mt7615 module in order to allow specifying driver specific
parameter.
This is a preliminary patch to add usb support to mt7921 driver.
Tested-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Switch to use le32/16_get_bits() to simplfy codes and specify
the size explicitly to avoid potential issues.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The original single LDPC cap bit cannot be used to
differentiate LDPC cap in each PHY mode.
This modification split the single bit into 3 bits,
ht_ldpc, vht_ldpc, and he_ldpc.
Reviewed-by: Ryder Lee <[email protected]>
Suggested-by: Money Wang <[email protected]>
Signed-off-by: MeiChia Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7663u_mcu_power_on utility routine since the code is shared
between mt7663u_mcu_init() and mt7663u_probe().
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Check return value of mt7615_mcu_restart routine in mt7663u_mcu_init().
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When operating on a mix of DFS and non-DFS channels, the driver only checks
the CAC status of the control channel. This causes beacons/tx to fail if the
control channel is on a non-DFS channel.
Fix this by calling cfg80211_reg_can_beacon to determine the DFS status of
all affected channels
Signed-off-by: Felix Fietkau <[email protected]>
The following error is see from the compiler:
mt7615/debugfs.c: In function ‘mt7615_ext_mac_addr_read’:
mt7615/debugfs.c:465:1: warning: the frame size of 1072 bytes is
larger than 1024 bytes [-Wframe-larger-than=]
The issue is due to allocating a buffer as string storage.
Fix by converting to a dynamical allocation of the buffer.
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add SAR spec support to mt7615 driver to allow configuring SAR power
limitations on the frequency ranges from the userland.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
