4addr is not supported by the offload firmware yet
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Without this change, garbage is seen in the hwmon name and sensors output
for mt7615 is garbled.
Fixes: 109e505ad944 ("mt76: mt7615: add thermal sensor device support")
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Maximum interval (in seconds) for schedule scan plan supported by
the offload firmware can be U16_MAX.
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Similar to mt7915, switching to use standard hwmon sysfs.
For reading temperature, cat /sys/class/ieee80211/phy*/hwmon*/temp1_input
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove MT76_STATE_PM in mt7615_init_device() and introduce
__mt7663s_mcu_drv_pmctrl for fw loading in mt7663s.
This patch fixes a crash at bootstrap for device (e.g. mt7622) that do
not support runtime-pm
Fixes: 129fac01ffe85 ("mt76: connac: introduce wake counter for fw_pmctrl synchronization")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Similar to mt7921, introduce awake and doze time accounting
for runtime pm.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Simplify the code using a wait_queue_head_t instead of a completion to
wait the chip is fully awake in mt76_connac_pm_wake routine
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7615_tx_worker routine as mt76 tx worker callback for
mt7663.
Rely on mt76_connac_pm_ref/mt76_connac_pm_unref to check PM state and
increment/decrement wake counter
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce a mutex in order to avoid a race between mt7615_mcu_lp_drv_pmctrl and
mt7615_mcu_fw_pmctrl routines since they are run two independent works
Fixes: 1f549009b5b2 ("mt76: mt7615: do not request {driver,fw}_own if already granted")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Frame reception timestamp (low 32-bits) that indicates the value of the
local TSF timer value at the time the first bit of the MAC header in the
received frame (PPDU unit) arriving at the MAC.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
After chip reset, the DMA scheduler needs to be initialized as well.
Since the code is PCI/SoC specific, move it to pci_mac.c, so that it
can depend on a function in dma.c
Signed-off-by: Felix Fietkau <[email protected]>
For AP and Client mode, the hardware can pass received packets
as 802.3 frames that can be passed to the network stack as-is.
Tested-by: Frank Wunderlich <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Set skb->ip_summed to CHECKSUM_UNNECESSARY if the hardware has validated
the IP and TCP/UDP checksum
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Enable hw rx-amsdu de-aggregation support.
This is a preliminary patch to enable rx checksum offload.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move hw_scan/sched_scan in mt76_connac_mcu module in order to be reused in
mt7615 and mt7921 drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt76_connac common mcu library for code sharing between mt7615 and
mt7921 devices
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
With a maximum length of 7991, the radio sometimes locks up under load when
transmitting A-MSDU frames to lots of stations. Using the lower limit makes
it work reliably again
Signed-off-by: Felix Fietkau <[email protected]>
Update mcu country code running mt7615_mcu_set_channel_domain routine in
mt7615_regd_notifier().
Filter out disabled channels in mt7615_mcu_set_channel_domain().
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move chainmask from driver phy to mt76_phy since it is used by all
drivers. This is a preliminary patch to create a common mcu library used
by mt7615 and mt7921 drivers
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mac_work delayed_work and mac_work_count in mt76_phy since it is
used by all drivers. This is a preliminary patch to create a common mcu
library used by mt7615 and mt7921 drivers
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to properly support mt7915 dbdc
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce dbdc support to mt7915 devices
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move hw data queues in mt76_phy from mt76_dev since mt7915 supports per
phy hw queues in dbdc mode
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When looking for a MAC address slot, start by using main BSSID slots 1-3,
afterwards use 16 repeater mode BSSID slots, then start using the slots
usually used for AP mode.
This search order should prevent unnecessary conflicts with AP mode interfaces
on the same PHY.
Note that two PHYs share global 32 omac slots with each other.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
After fixing mac80211 to allow larger A-MSDUs in some cases, there have been
reports of performance regressions and packet loss with some clients.
It appears that the issue occurs when the hardware is transmitting A-MSDUs
bigger than 8k. Limit the local VHT MPDU size capability to 7991, matching
the value used for MT7915 as well.
Signed-off-by: Felix Fietkau <[email protected]>
Unlock dfs channels for mt7615 devices since the driver supports
radar detection. Dfs pattern detector has been tested successfully by
mt7615 users.
Do not unlock DFS frequencies for mt7663 devices since it has not been
tested yet.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce idle-timeout knob in mt7615 debugfs in order to configure the
idle time to switch to low-power state
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Check MT76_STATE_PM in mt7615_driver_own/mt7615_firmware_own
in order to not requested power ownership if it is already granted
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Queue frames pushed by mac80211 running mt7615_tx if the device is
low-power state. Run wake workqueue in order to swicth to full-power
before transmitting pending frames
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Make sure to run mt7615_dfs_init_radar_detector in mt7615_regd_notifier
holding mt76 mutex in order to avoid races and set the device in full
power
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce runtime-pm power_save delayed work used to enable
low-power after an inactivity period
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7615_pm_wake utility routine to wake the device from
runtime low-power state (lower-power state is currently supported by
offload firmware for pcie devices).
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Supports sending a configurable number of packets with a specific rate
and configurable tx power levels / antenna settings, as well as displaying
rx statistics.
Signed-off-by: Felix Fietkau <[email protected]>
Limits are used to update the channel max_power settings and also passed
to the firmware on channel changes
Signed-off-by: Felix Fietkau <[email protected]>
switch to per-vif ps support since mt7615 offload firmware can handle it
properly. This patch allows enabling/disabling power-save support on p2p
interface
Tested-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce remain_on_channel support to mt7615 driver if the device is
running offload firmware
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix typo defining ps_work in mt7615_register_ext_phy(). This is not a
real issue since 802.11 power save is not yet support by the external phy
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix mt7663 eeprom definitions for delta tx power parsing
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
