Similar to MT7915, enable Wireless Ethernet Ditpatcher for MT7996
to offload traffic received from the WLAN nic and transmitted on the
LAN one
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Co-developed-by: Sujuan Chen <[email protected]>
Signed-off-by: Sujuan Chen <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce WED rx support for mt7996
driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Per peer Tx/Rx statistic can only be obtained by querying WM when WED is
on. This patch switches to periodic event reporting in the case of WED
being enabled.
Signed-off-by: Yi-Chia Hsieh <[email protected]>
Signed-off-by: Money Wang <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Evelyn Tsai <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Do not report cca and csa finish to upper layer on station type vif to
prevent warnings caused by setting beacon.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use the correct ieee80211_conf of each band for IEEE80211_CONF_MONITOR
comparison.
Fixes: 24e69f6bc3ca ("mt76: fix monitor rx FCS error in DFS channel")
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When the set_chan_info command is set with CH_SWITCH_NORMAL reason,
even if the action is UNI_CHANNEL_RX_PATH, it'll still generate some
unexpected tones, which might confuse DFS CAC tests that there are some
tone leakages. To get rid of these kinds of false alarms, always bypass
DPD calibration when IEEE80211_CONF_IDLE is set.
Reviewed-by: Evelyn Tsai <[email protected]>
Signed-off-by: StanleyYP Wang <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add CAP3_RX_CTRL_FRAME_TO_MULTIBSS check when setting sta_muru_tlv,
which is used to get stations's capability of receiving control frames
when running OFDMA with MBSSIDs.
Signed-off-by: Allen Ye <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add support to configure parameters at runtime, such as mcs, gi, and
he_ltf. Note that EHT mode does not support this feature yet.
Co-developed-by: MeiChia Chiu <[email protected]>
Signed-off-by: MeiChia Chiu <[email protected]>
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The bf_num field represents how many bands can support beamform, so set
the value to 3, and bf_bitmap represents the bitmap of bf_num.
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce mt76_connac3 mac library used
by WiFi7 chipsets (e.g. mt7996).
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
If driver directly uses the band_idx reported from the radar event to
access mt76_phy array, it will get the wrong phy for background radar.
Fix this by adjusting the statement.
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: StanleyYP Wang <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
There's a race between driver and fw on some tx/rx control registers
when setting ifs, which will cause accidental hw queue pause problems.
Avoid this by setting ifs time with bss_info mcu command.
Reviewed-by: Shayne Chen <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The bmc_tx_wlan_idx should be the wlan_idx of the current bss rather
than peer AP's wlan_idx, otherwise there will appear some frame
decryption problems on station mode.
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Reviewed-by: Shayne Chen <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add FW_START_WORKING_PDA_DSP for the indication of starting DSP
firmware download, which is for phy-related control.
The firmware is transparent to the driver, but it's necessary for the
firmware download process.
Reviewed-by: Shayne Chen <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Similar to BSS_CHANGED_BASIC_RATES, this enables mcast rate
configuration through fixed rate tables.
Signed-off-by: Ryder Lee <[email protected]>
Change-Id: Ifc305e8c7de9a7df4ad5f856e2097d721a886aaa
Signed-off-by: Felix Fietkau <[email protected]>
The connac3 removes fixed rate fields to reduce txd size and introduces
global rate tables (64 entries) for rate setting. Driver needs to fill
the corresponding idx in MT_TXD6_TX_RATE while tx, and push mt76_rate
into predifined table at bootup stage so that mvif->basic_rates_idx
can immediately switch out once setting changes.
spe_idx is also needed for fixed rate frames, and will be updated by
future patches.
Note that all table entries are shared across driver and firmware
(i.e.TxBF), hence adding MT7996_BASIC_RATES_TBL to reflect mapping
status.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add testing points into debugfs to trigger firmware assert and enable
full system recovery. Also rename knob "fw_ser" to a clear-cut name
"sys_recovery".
Co-developed-by: Bo Jiao <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add mt7996_reset() and refactor mt7996_mac_reset_work() to support
full system recovery.
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce p2p-go/p2p-client support to mt7921 driver
CONNECTION_P2P_GC/GO is not supported with the current firmware
so we added mt76_dev to mt76_connac_mcu_sta_basic_tlv signature to
use CONNECTION_INFRA_STA/AP instead for p2p-client and p2p-go
respectively to make it work.
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Currently using BSS_INFO_PS command will sometimes cause packet drop in
hw rx queue.
Temporarily remove this function until finding the cause.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix the tail and data pointers. The rxd->len in mt7996_mcu_rxd does not
include the length of general rxd. It only includes the length of
firmware event rxd. Use skb->length to get the correct length.
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Pass qid into mt7996_mac_write_txwi() to let the tx descriptor of
non-bufferable MMPDUs be filled with correct hw queue index.
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Those capabilities have been added into ieee80211_bss_conf.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
There are variants of mt7996 which are different from eht supported and
wtbl size limit. Get the hw caps with CHIP_CONFIG command.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Run mt7996_mcu_restart routine directly and avoid mcu_restart function
pointer whenever it is possible.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Check return value of mt7996_mcu_get_eeprom_free_block() first before
accessing free_block_num.
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Coverity message:
using tainted "r->band_idx" variable as an index into an array "(*dev).mt76.phys".
Reported-by: coverity-bot <[email protected]>
Addresses-Coverity-ID: 1527812 ("Insecure data handling")
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Coverity message:
using tainted "hdr->band" variable as an index into an array "(*dev).mt76.phys".
Reported-by: coverity-bot <[email protected]>
Addresses-Coverity-ID: 1527797 ("Insecure data handling")
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The SPR parameter set comprises OBSS PD threshold for SRG and
non SRG and Bitmap of BSS color and partial BSSID. This adds
support to configure fields of SPR element to firmware.
User can disable firmware SR algorithms by turning sr_scene_detect off.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
