The mtcl table, configured by platform vendor, provides regulatory
information for 5.9/6 GHz channels. mt792x should work on
corresponding channels supported by mtcl. This patch would parse
the settings in mtcl table and apply the result into chip side.
Signed-off-by: Rong Yan <[email protected]>
Co-developed-by: Deren Wu <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The 5.9/6GHz channel license of a certain platform device has been
regulated in various countries. That may be difference with standard
Liunx regulatory domain settings. In this case, when .reg_notifier()
called for regulatory change, mt792x chipset should update the channel
usage based on clc or dts configurations.
Channel would be disabled by following cases.
* clc report the particular UNII-x is disabled.
* dts enabled and the channel is not configured.
Signed-off-by: Ming Yen Hsieh <[email protected]>
Co-developed-by: Deren Wu <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The clc event can report the radio configuration for the corresponding
country and the driver would take it as regulatory information of a
certain platform device.
This patch would change the clc commnad from no-waiting to waiting for
event. For backward compatible, we also add a new nic capability tag
to indicate the firmware did support this new clc event from now on.
Signed-off-by: Ming Yen Hsieh <[email protected]>
Co-developed-by: Deren Wu <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
There are several power type should be supported in 6GHz band. mt7921
apply 6GHz power type from AP settings and clc will setup the
corresponding regulatory power.
Signed-off-by: Ming Yen Hsieh <[email protected]>
Co-developed-by: Deren Wu <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt76_connac_mcu_get_nic_capability() is used by mt7921 only. It
would be better to put the code in chip folder. And we can provide
more chip capability information in mt792x_phy without making
mt76_phy much bigger.
The three functions would be moved to mt7921 folder and renamed.
mt76_connac_mcu_parse_tx_resource()
mt76_connac_mcu_parse_phy_cap()
mt76_connac_mcu_get_nic_capability()
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
MT7921_PM_TIMEOUT is shared between mt7925 and mt7921 so move it in
mt792x module.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt7921_load_firmware routine is shared between mt7921 and mt7925 chipset
so move it in mt792x-lib module.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move acpi_sar code in mt792x-lib module since it is shared between
mt7921 and mt7925 driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Moving hif_ops marcos in mt792x.h, we can move shared runtime-pm code
between mt7925 and mt7921 in mt792x-lib module.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Reduce duplicated code moving mac shared code in mt792x-lib module.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt792x-lib module will contain the shared code between mt7921 and new
MT79 WiFi7 chipset
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce WiFi7 chipset support
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce WiFi7 chipset support
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce WiFi7 chipset support
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce WiFi7 chipset support
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
For some cases as below, we may encounter the unpreditable chip stats
in driver probe()
* The system reboot flow do not work properly, such as kernel oops while
rebooting, and then the driver do not go back to default status at
this moment.
* Similar to the flow above. If the device was enabled in BIOS or UEFI,
the system may switch to Linux without driver fully shutdown.
To avoid the problem, force push the device back to default in probe()
* mt7921e_mcu_fw_pmctrl() : return control privilege to chip side.
* mt7921_wfsys_reset() : cleanup chip config before resource init.
Error log
[59007.600714] mt7921e 0000:02:00.0: ASIC revision: 79220010
[59010.889773] mt7921e 0000:02:00.0: Message 00000010 (seq 1) timeout
[59010.889786] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59014.217839] mt7921e 0000:02:00.0: Message 00000010 (seq 2) timeout
[59014.217852] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59017.545880] mt7921e 0000:02:00.0: Message 00000010 (seq 3) timeout
[59017.545893] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59020.874086] mt7921e 0000:02:00.0: Message 00000010 (seq 4) timeout
[59020.874099] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59024.202019] mt7921e 0000:02:00.0: Message 00000010 (seq 5) timeout
[59024.202033] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59027.530082] mt7921e 0000:02:00.0: Message 00000010 (seq 6) timeout
[59027.530096] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59030.857888] mt7921e 0000:02:00.0: Message 00000010 (seq 7) timeout
[59030.857904] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59034.185946] mt7921e 0000:02:00.0: Message 00000010 (seq 8) timeout
[59034.185961] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59037.514249] mt7921e 0000:02:00.0: Message 00000010 (seq 9) timeout
[59037.514262] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59040.842362] mt7921e 0000:02:00.0: Message 00000010 (seq 10) timeout
[59040.842375] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59040.923845] mt7921e 0000:02:00.0: hardware init failed
Fixes: 5c14a5f944b9 ("mt76: mt7921: introduce mt7921e support")
Tested-by: Kai-Heng Feng <[email protected]>
Co-developed-by: Leon Yen <[email protected]>
Signed-off-by: Leon Yen <[email protected]>
Signed-off-by: Quan Zhou <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Tested-by: Juan Martinez <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move some mac shared definitions between mt7996, mt7921 and mt7915 in
mt76_connac2_mac.h.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
eeprom.h is mostly empty for mt7921, so get rid of it.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mcu_uni_event and mcu_reg_event structs are shared between mt7921 and
mt7615 drivers, so move them in connac lib.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The rx filter, in mt7921 series, may be changed in fw operation. There is
a racing problem if rx filter controlled by both driver and firmware at
the same time. To avoid this issue, let mt7921 driver set rx filter by new
command MCU_CE_CMD_SET_RX_FILTER and allow the firmware controlling it
only.
Reviewed-by: Lorenzo Bianconi <[email protected]>
Co-developed-by: Deren Wu <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Neil Chen <[email protected]>
Tested-by: AngeloGioacchino Del Regno <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
round_jiffies_up() may change the duration reported from chip. We should
take the real timeout for current channel privilege.
Fixes: 034ae28b56f1 ("wifi: mt76: mt7921: introduce remain_on_channel support")
Signed-off-by: Deren Wu <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When the chanctx enabled, IEEE80211_CONF_CHANGE_CHANNEL in .config()
would not be called anymore. mt76 cannot control RF channel for monitor.
Add monitor type set-channel flow in .change_chanctx().
Fixes: 41ac53c899bd ("wifi: mt76: mt7921: introduce chanctx support")
Reviewed-by: Sean Wang <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In ACPI enabled devices, mt7921 should read MTFG table from platform
hardware. Apply necessary settings for firmware capabilities through CLC
command.
Co-developed-by: Deren Wu <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Quan Zhou <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce remain_on_channel support. Additionally, we add
mt7921_check_offload_capability to disable .remain_on_channel and
.cancel_remain_on_channel and related configuration because those
operations would rely on the fundamental MCU commands that will be only
supported with newer firmware.
Co-developed-by: Deren Wu <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The firmware would be in charge of braking and continuing the traffic while
the channel contexts are switching between different BSS and HW SCAN in the
background.
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Country Location Control (CLC) is an additional control for country rules
in firmware. We introduce this new feature to make sure mt7921 series
working properly in all region.
The addtional policies would be put into firmware based on differnt
regions. mt76 driver should be in charge of submitting per region policy.
Reviewed-by: Sean Wang <[email protected]>
Tested-by: YN Chen <[email protected]>
Co-developed-by: Deren Wu <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The current driver has worked with HW beacon filter and connection
monitor all the way, here we move the enablement into the initialization
stage like other HW features being done to get rid of others are
confused why these configurations would be changed at runtime.
We still leave a way to turn off these offload features in debugfs knobs
but that is just for debugging purposes.
Tested-by: Deren Wu <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Previously the code used skb_set_queue_mapping for management or non-bufferable
powersave frames that need to be sent to a different hardware queue.
This can confuse AQL, which expects the value to remain the same until the tx
status report.
The only place that currently uses the altered skb queue mapping is the txwi
write function. Change the code to pass the hardware queue id as a function
parameter instead.
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_connac2_mcu_fill_message routine in shared module in order to
reuse it for mt7921 and mt7915e drivers. This is a preliminary patch to
add mt7990 driver support.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to add mt7990 chipset support.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Due to AP stop improperly, mt7921 driver would face random command timeout
by chip fw problem. Migrate AP start/stop process to .start_ap/.stop_ap and
congiure BSS network settings in both hooks.
The new flow is shown below.
* AP start
.start_ap()
configure BSS network resource
set BSS to connected state
.bss_info_changed()
enable fw beacon offload
* AP stop
.bss_info_changed()
disable fw beacon offload (skip this command)
.stop_ap()
set BSS to disconnected state (beacon offload disabled automatically)
destroy BSS network resource
Fixes: 116c69603b01 ("mt76: mt7921: Add AP mode support")
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Beacon disable flow would be handled in bss stop handler automatically.
Force return -EOPNOTSUPP in disable case.
Fixes: 116c69603b01 ("mt76: mt7921: Add AP mode support")
Reviewed-by: Sean Wang <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mac_write_txwi code is shared between connac2 devices (mt7915 and
mt7921). Move it in connac module.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to share txwi configuration code.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_connac2_load_patch utility routine in mt76_connac module since
it is shared between mt7921 and mt7915. This is a preliminary patch to
support mt7902e driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_connac2_load_ram utility routine in mt76_connac module since
it is shared between mt7921 and mt7915. This is a preliminary patch to
support mt7902e driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move drv_own/fw_own toggle in mt7921_load_firmware. This change allow to
reuse connac code to load patch for mt7921 driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Tested-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_connac2 fw structures in connac module since they are shared
between mt7921 and mt7915 drivers. This is a preliminary patch to add
mt7902e support.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
To avoid racing problems in chip, mt7921s should reacquire drv-own after
firmware semaphore is released.
Fixes: 78b217580c509 ("mt76: mt7921s: fix bus hang with wrong privilege")
Signed-off-by: YN Chen <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add ipv6 NS offload for WoWLAN state.
Tested in this way:
1. Put device-A into WoW state.
2. ping6 from device-B to device-A.
3. In sniffer, see Neighbour advertisement from device-A.
Reviewed-by: Sean Wang <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When setup monitor mode in DFS channel, mt76 send CH_SWITCH_DFS to
fw for channel config. This would cause rx performance bad while
monitoring frames. Settings CH_SWITCH_NORMAL in monitor mode would
get the same performance as normal channels.
Reviewed-by: Shayne Chen <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
