Rename MT_WFDMA0_CSR_TX_DMASHDL_ENABLE to
MT_WFDMA0_GLO_CFG_EXT0_CSR_TX_DMASHDL_EN to follow the register
naming convention (parent register name as prefix).
This is a preparation patch before enabling MT7928 PCIe support.
Signed-off-by: Emery Hsin <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Replace hardcoded MT_PCIE_MAC_INT_ENABLE and MT_PCIE_MAC_PM macros
with a per-chip mt792x_pcie_reg struct. Remove the shared macros
from mt792x_regs.h and update mt792x_wpdma_reinit_cond() to use
dev->pcie_reg.
This is a preparation patch before enabling MT7928 PCIe support.
Signed-off-by: Emery Hsin <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Add the MT7927-specific PCIe DMA queue layout and local DMA setup,
including the extra RX ring and WFDMA/prefetch programming.
MT7927 does not follow the mt7925 DMA configuration, so provide a
separate DMA init path while reusing the existing common queue setup.
This keeps the chip-specific changes local and prepares the driver
for later MT7927 enablement without affecting existing devices.
Co-developed-by: Javier Tia <[email protected]>
Signed-off-by: Javier Tia <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Add a dedicated MT7927 WFSYS reset path in mt792x_wfsys_reset().
Unlike the existing connac2/connac3 reset flow that toggles the WFSYS
software reset bit and waits for init-done, MT7927 reset is driven
through CBInfra and requires polling ROMCODE_INDEX until the MCU returns
to the idle value after reset.
Keep this dormant for now: no MT7927 PCI IDs are added by this patch, so
it only prepares the reset logic without making the driver bind to MT7927
hardware yet.
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
The mac_reset and resume paths use the hardcoded MT_INT_RX_DONE_ALL
constant (bits 0-2) to re-enable RX interrupts. This is correct for
MT7925 (RX rings 0, 1, 2) but wrong for chips using different ring
indices.
Define a per-chip irq_map with the correct RX interrupt enable bits and
replace hardcoded MT_INT_RX_DONE_ALL with irq_map field reads in the
resume and mac_reset paths. Add the MT7927 irq_map with interrupt bits
matching its RX ring layout (rings 4, 6, 7), selected at probe time
based on PCI device ID.
This ensures the correct interrupt bits are enabled regardless of the
chip variant.
Tested-by: Marcin FM <[email protected]>
Tested-by: Cristian-Florin Radoi <[email protected]>
Tested-by: George Salukvadze <[email protected]>
Tested-by: Evgeny Kapusta <[email protected]>
Tested-by: Samu Toljamo <[email protected]>
Tested-by: Ariel Rosenfeld <[email protected]>
Tested-by: Chapuis Dario <[email protected]>
Tested-by: Thibaut François <[email protected]>
Tested-by: 张旭涵 <[email protected]>
Reviewed-by: Sean Wang <[email protected]>
Signed-off-by: Javier Tia <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
mt7925u uses different reset/status registers from mt7921u. Reusing the
mt7921u register set causes the WFSYS reset to fail.
Add a chip-specific descriptor in mt792xu_wfsys_reset() to select the
correct registers and fix mt7925u failing to initialize after a warm
reboot.
Fixes: d28e1a48952e ("wifi: mt76: mt792x: introduce mt792x-usb module")
Cc: [email protected]
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Add a dummy register read in mt76_connac_mcu_rate_txpower_band() to act as
a PSE barrier. This would release PSE pages and prevents buffer underflow
issues when handling MCU commands with larger payloads without the response
in mt76_connac_mcu_set_rate_txpower().
This is a prerequisite patch before enabling MT7902 PCIe and SDIO support.
Co-developed-by: Xiong Huang <[email protected]>
Signed-off-by: Xiong Huang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
MediaTek has asked to switch from the ISC license to BSD-3-Clause-Clear,
in order to improve clarity and the legal integrity of the code.
The BSD-3-Clause license includes the "no endorsement" clause, which is
important for protecting the reputation of the original authors and
contributors by preventing unauthorized use of their names for endorsement
purposes.
This clause is absent in the BSD-2-Clause license, which is more permissive
but lacks this specific protection.
This change also cleans up the license of some Kconfig/Makefile files,
which were accidentally marked as GPL.
The GPL 2.0 remains in use on mt76x0, as well as two source files in mt7615
for which the license situation still needs to be clarified.
Signed-off-by: Felix Fietkau <[email protected]>
A sub-process of Wifi L0.5 reset will make chip common partition
enter low power, and have chance lead to Bluetooth host-to-chip
command timeout, modify the software flow according to the chip's
design to solve the problem.
Fixes: c948b5da6bbe ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Signed-off-by: Quan Zhou <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt792x_irq_map will be use to share the irq code shared between mt7921
and mt7925
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt792x-lib module will contain the shared code between mt7921 and new
MT79 WiFi7 chipset
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch in order to support new WiFi7 chips.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
