Unlike on earlier chips, DMA completion on MT7615 does not imply actually
having sent out any packets.
Since AQL will prevent filling the hardware queues and will only allow more
packets to be passed to the driver after tx completion, it makes much more
sense to schedule the tx tasklet there.
This is also needed for scheduling tx in testmode support
Signed-off-by: Felix Fietkau <[email protected]>
Overwrite hw queue id for non-bufferable management frames if the hw
support always txq (altxq) in order to be in sync with mac txwi code
Fixes: cdad4874057d ("mt76: mt7615: add dma and tx queue initialization for MT7622")
Fixes: f40ac0f3d3c0 ("mt76: mt7615: introduce mt7663e support")
Suggested-by: Felix Fietkau <[email protected]>
Tested-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Since usb code can't access device registers in interrupt context, move
rcu_read_lock/rcu_read_unlock in mt7615_poll_tx routine. Moreover loop
over a local msta list in mt7615_mac_sta_poll since mt7663u driver will
not be able to complete the inner while loop before sta_poll_list list
is refilled by mt7615_mac_add_txs/mt7615_mac_fill_rx
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In VHT mode we can receive larger MPDUs. Increasing the buffer size reduces
fragmentation here, which should improve performance.
Signed-off-by: Felix Fietkau <[email protected]>
Create mt7615-common module in order to collect shared code between usb
and mmio code. Move the following source files in mt7615-common module:
- main.c
- init.c
- mcu.c
- mac.c
- debugfs.c
- eeprom.c
- trace.c
Create the following source files for mmio only source code and move them
in mt7615e module:
- pci_init.c
- dma.c
- pci_mac.c
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When the firmware detects a problem, it needs the host to stop/reset DMA and
resume it again when the hardware state has been reset.
Signed-off-by: Felix Fietkau <[email protected]>
MT7622 queue mapping is different from MT7615 and requires an extra dma
scheduler init and a few register tweaks
Co-developed-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Poll per-station hardware counters available in WTBL after tx/rx
status events in order to report tx/rx airtime to mac80211 layer
Co-developed-by: Felix Fietkau <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76{15,03}_tx_tasklet in mt76_alloc_device in order to be used as
default tx_tasklet initialization. Remove duplicated code in
mt7603/mt7615 drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add hw radar detection support to mt7615 driver in order to
unlock dfs channels on 5GHz band
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move netif_napi_del in mt76_dma_cleanup routine since it is done
by all drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This allows tx scheduling and tx cleanup to run concurrently
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This driver is for a newer generation of MediaTek MT7615 4x4 802.11ac
PCIe-based chipsets, which support wave2 MU-MIMO up to 4 users/group
and also support up to 160MHz bandwidth.
The driver fully supports AP, station and monitor mode.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Roy Luo <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
