mt7921 is currently using rxfilter defined in mt76_dev for rx filter
configuration. Fix mt7921_configure_filter implementation.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Firmware initialization can take a while. Move mt7921_init_hw routine in
a dedicated work in order to not slow down bootstrap process.
Tested-by: Deren Wu <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Properly set up the monitor mode the firmware can support to fix up
RTS/CTS and beacon frames cannot be captured and forwarded to the host.
Tested-by: Deren Wu <[email protected]>
Tested-by: Sven Eckelmann <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt76_connac_lmac_mapping is shared between mt7921 and mt7915
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Toggle runtime-pm and deep-sleep configuration adding/removing
a montior vif in order to forward all tx/rx frames to mac80211.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Tested-by: Sven Eckelmann <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
It doesn't guarantee the mt7921e gets started with ASPM L0 after each
machine reboot on every platform.
If mt7921e gets started with not ASPM L0, it would be possible that the
driver encounters time to time failure in mt7921_pci_probe, like a
weird chip identifier is read
[ 215.514503] mt7921e 0000:05:00.0: ASIC revision: feed0000
[ 216.604741] mt7921e: probe of 0000:05:00.0 failed with error -110
or failing to init hardware because the driver is not allowed to access the
register until the device is in ASPM L0 state. So, we call
__mt7921e_mcu_drv_pmctrl in early mt7921_pci_probe to force the device
to bring back to the L0 state for we can safely access registers in any
case.
In the patch, we move all functions from dma.c to pci.c and register mt76
bus operation earilier, that is the __mt7921e_mcu_drv_pmctrl depends on.
Fixes: bf3747ae2e25 ("mt76: mt7921: enable aspm by default")
Reported-by: Kai-Chuan Hsieh <[email protected]>
Co-developed-by: Deren Wu <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Similar to mt7915 driver, process txfree and txstatus without allocating
skbs in order to reduce pressure on the memory allocator
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_connac_mcu_restart routine in mt76-connac since it is shared
between mt7921 and mt7915.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove mt7921_mcu_get_eeprom since it is no longer used.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move key configuration code shared between mt7921 and mt7915 in
mt76-connac module and remove duplicated code.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
TXS in mt7921 may be forwared to tx_done event. Should try to catch
TXS information in tx_done event as well.
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
There is a missing mt7921e_driver_own in the MT7921E reset procedure
since the mt7921 mcu.c has been refactored for MT7921S, that will
result in MT7921E reset failure, so add it back now.
Fixes: dfc7743de1eb ("mt76: mt7921: refactor mcu.c to be bus independent")
Reported-by: YN Chen <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move tx_amsdu histogram stats in mib_stats structure since registers are
clear-on-read
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to add ethtool stats to mt7921 driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce ethtool stats support to mt7921
driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce mt7921s support.
Refactor mt7921_mcu_send_message to be sharable between mt7921s and
mt7921e.
Tested-by: Deren Wu <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rely on mcu_get_nic_capability to obtain Tx quota information
for the SDIO device, get PHY capability, MAC address and then we can
totally drop mt7921/eeprom.c and any unnecessary code.
Noting that mt76_connac_mcu_get_nic_capability should be run before set
flag MT76_STATE_MCU_RUNNING being set to setup the proper parameters
like Tx quota control before the device is started to running.
Tested-by: Deren Wu <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce mt7921s support.
Make init.c reusable between mt7921s and mt7921e
Tested-by: Deren Wu <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce mt7921s support.
Make mcu.c reusable between mt7921s and mt7921e
Tested-by: Deren Wu <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce mt7921s support.
make dma.c be used dedicately for mt7921e.
by moving out mt7921_tx_cleanup from dma.c to mcu.c and then renaming
mt7921_tx_cleanup to refect the exact thing the function actually does.
Finally, dma.c totally become pcie specific one, only needed to
be compiled only when CONFIG_MT7921E is enabled.
Tested-by: Deren Wu <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce mt7921s support.
Split out a new pci_mac.c from mac.c to make mac.c reusable between
mt7921s and mt7921e.
Tested-by: Deren Wu <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Unlock 6GHz band if supported by the device. Configure HE 6G
capabilities.
Tested-by: Deren Wu <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Robustify hardware initialization in the current driver probing flow
to get rid of the device is possibly lost after the machine boot due
to possible firmware abnormal state by trying to recover the failure
with more chances.
Tested-by: Leon Yen <[email protected]>
Tested-by: YN Chen <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove unused tx rate reporting through mcu tx done event since
now tx status is fully supported
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Report tx rate from tx status packets instead of receiving periodic mcu
event. This improves flexibility, accuracy and AQL performance, and
simplifies code flow for better readability.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce infrastructure support for tx status reporting
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Similar to mt7915, introduce mt7921_txwi_free to report tx rate to
mac80211. This is a preliminary patch to add proper tx status report.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt7921 mac work can be idle for a long time due to runtime-pm so
update mib counters dumping phy stats
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
As for 7915 moving mt7921_queue_rx_skb makes it possible to make
some functions in mac.c static
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7921_mcu_set_beacon_filter utility routine in order to
remove duplicated code for hw beacon filtering.
Move mt7921_pm_interface_iter in debugfs since it is just used there.
Make the following routine static:
- mt7921_pm_interface_iter
- mt7921_mcu_uni_bss_bcnft
- mt7921_mcu_set_bss_pm
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove mt7921_mac_set_beacon_filter routine since it is no longer used.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove monitor_vif pointer from mt7921 since it is just a leftover of
initial porting.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add new chip mt7922 in mt7921 module with following items
1. new chip ID / fw bin name
2. is_mt7922()
check chip type for different fw files
3. mt7921_get_data_mode()
check security type of fw (backward compatible)
Co-developed-by: Jimmy Hu <[email protected]>
Signed-off-by: Jimmy Hu <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix the current driver mgmt frame is not respecting the basic rates field
provided by the AP and then unconditionally is using the lowest (1 or 6
Mbps) rate.
For example, if the AP only supported basic rate {24, 36, 48, 54} Mbps,
mt7921 cannot send mgmt frame with the rate not in the group. So,
instead, we pick up the lowest basic rate the AP can support to send.
Fixes: 163f4d22c118 ("mt76: mt7921: add MAC support")
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Disable chip full reset just during device probing but allow
it during hw restart.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When .sta_state is implemented, mac80211 assumes that the station entry is
usable after the NOTEXIST->NONE transition.
So we should create the sta entry as early as possible in order that
mac80211 pass assoc/auth frames to mt76 with the newly created sta entry,
and add .sta_assoc to mt76 core to refresh the sta entry again when sta is
being associated.
Fixes: 8aa5a9b7361c ("mt76: mt7921: enable deep sleep at runtime")
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Make mt7921_set_channel routine static since it is only used in main.c
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
