Introduce mt7915_mcu_rdd_background_enable and
mt7915_mcu_background_chain_ctrl routines to configure rx dfs dedicated chain.
This is a preliminary patch to add zero-wait dfs support performing CAC
detection on rdd2.
Tested-by: Owen Peng <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Without this change, it sends the wrong SMPS mode to firmware
when a station sends an action frame with disabled SMPS.
Fixes: 427b09cd6bfa ("mt76: mt7915: fix SMPS operation fail")
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: MeiChia Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Load the default eeprom data when the content of flash/efuse is invalid.
This could help to eliminate some issues due to incorrect or
insufficient rf values.
Co-developed-by: Bo Jiao <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
TGn fails sending SM power save mode action frame to the AP to switch
from dynamic SMPS mode to static mode.
Reported-by: Fang Zhao <[email protected]>
Signed-off-by: Fang Zhao <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add debugfs knobs to read MCU utilization, which helps user know
firmware status more easily to narrow down CPU bottleneck issues.
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
With this patch, driver can support single rate, (HE)GI and HE_LTF
configuration through .set_bitrate_mask().
Tested-by: MeiChia Chiu <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Enable HE UL MU-MIMO in sta_rec_muru, which works on both ap and station
mode.
For sending trigger frames, one of the conditions fw uses is to check if
mib rx airtime meets the threshold.
There's a main control of mib rx airtime report register in fw, so we
need to enable the register by mcu cmd instead of directly writing it,
otherwise it will still be disabled by fw.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rework starec tags to the order which firmware expected. This also fixes
some weird behaviors during generating SPL of HE-MU.
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
With this patch we can append txbf starec TLVs. This is an intermediate
patch to improve HE MUMIMO performances.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mcu APIs to configure bss coloring and to report bss coloring
collisions. Add support to report coloring countdown in beacon sent by
the device.
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Switch proper tx arbiter mode during testmode tx to prevent from
entering the flow of normal tx in FW.
Also, testmode SU and MU tx need to use different arbiter mode.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Report tx rate from tx status packets instead of receving periodic mcu
event. This improves flexibility, accuracy and AQL performance, and
simplifies code flow for better readability.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The newer firmware requires host driver to set BA winsize
on both Tx/Rx sessions, so modify it for the long run.
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Sujuan Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:114:10: error: implicit
conversion from enumeration type 'enum mt76_cipher_type' to different
enumeration type 'enum mcu_cipher_type' [-Werror,-Wenum-conversion]
return MT_CIPHER_NONE;
~~~~~~ ^~~~~~~~~~~~~~
drivers/net/wireless/mediatek/mt76/mt7921/mcu.c:114:10: error: implicit
conversion from enumeration type 'enum mt76_cipher_type' to different
enumeration type 'enum mcu_cipher_type' [-Werror,-Wenum-conversion]
return MT_CIPHER_NONE;
~~~~~~ ^~~~~~~~~~~~~~
Fixes: c368362c36d3 ("mt76: fix iv and CCMP header insertion")
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The iv from RXD is only for TKIP_RSC/CCMP_PN/GCMP_PN, and it needs a
check for CCMP header insertion. Move mt76_cipher_type to mt76.h to
reduce duplicated code.
Signed-off-by: Xing Song <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use mt7915_mcu_set_txbf() to reduce global functions. This can be
easily extended to support other TxBF commands in further patches.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Firmware functions (SCS, MU ...) also require read-clear phy counters,
hence firmware prepares a global task to read shared fields out to a
shared pool to avoid concurrency. Switch to event format accordingly.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Thermal cooling device support is added to control the temperature by
throttling the data transmission for the given duration. Throttling is
done by adjusting Tx period by given percentage of time. The thermal
device allows user to configure duty cycle.
Throttling can be disabled by setting the duty cycle to 0. The cooling
device can be found under /sys/class/thermal/cooling_deviceX/.
Corresponding soft link to this device can be found under phy folder
To set duty cycle as 80%,
echo 80 > /sys/class/ieee80211/phy*/cooling_device/cur_state
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove obsoleted codes. This is the preparation for .set_bitrate_mask().
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When the EEPROM data is read from flash, it can contain pre-calibration
data, which can save calibration time.
Note that group_cal can save 30% bootup calibration time, and dpd_cal can
save 75% channel switching time.
Tested-by: Bo Jiao <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
It causes high CPU load on the WA core, which can lead to extra latency when
using many stations. Dropping packets for long queues is managed by mac80211
fq_codel instead
Signed-off-by: Felix Fietkau <[email protected]>
Add support for passing flags for selecting the MCU target and query type
instead of trying to detect it based on the command id
Signed-off-by: Felix Fietkau <[email protected]>
Add a testmode mcu command to clean up hw tx queue before a new
testmode tx starts.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add support to calculate and apply ipg parameters in testmode
for MT7915 NIC.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Split parameter settings and mcu command update in mt7915_mcu_set_tx().
This is for reusing edca update function in testmode ipg setting.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add support for getting rf values from flash.
This is used for some test purposes and products.
If the mtd partition is configured in dts, driver will read from flash
to init eeprom command; if not, still init it with efuse's values.
An example:
&slot0 {
mt7915@0,0 {
reg = <0x0000 0 0 0 0>;
device_type = "pci";
mediatek,mtd-eeprom = <&factory 0x0000>;
};
};
Acked-by: Ryder Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt7915_mcu_bss_sync_tlv() is no longer used, so remove it.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Support to set tx frequency offset in testmode, which is usally used in
the pre-calibration stage.
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Support testmode tx for MT7915A, including tx streams and HE rate
settings.
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When per-packet rate reporting is enabled, the hardware can get stuck under
some conditions. It self-recovers quickly, but in practice this leads to
reduced performance.
In order to avoid running into this issue, disable per-packet rate reporting
by default and query the rx rate from firmware instead, unless monitor mode
is enabled.
Signed-off-by: Felix Fietkau <[email protected]>
When looking for a MAC address slot, start by using main BSSID slots 1-3,
afterwards use 16 repeater mode BSSID slots, then start using the slots
usually used for AP mode.
This search order should prevent unnecessary conflicts with AP mode interfaces
on the same PHY
Signed-off-by: Felix Fietkau <[email protected]>
