Reset per-phy mac address slot mask in order to avoid leaking entries.
Fixes: 8a55712d124f ("wifi: mt76: mt7915: enable full system reset support")
Signed-off-by: Felix Fietkau <[email protected]>
It seems that the firmware checks the register used for detecting matching
PCIe links in order to figure out if a secondary PCIe link is enabled.
Write the register again just before starting the firmware on hw reset,
in order to fix an issue that left the second band unusable after restart.
Fixes: 9093cfff72e3 ("mt76: mt7915: add support for using a secondary PCIe link for gen1")
Signed-off-by: Felix Fietkau <[email protected]>
Due to a limitation in available memory, the MT7916 firmware can only
handle either 5 GHz or 6 GHz at a time. It does not support runtime
switching without a full restart.
On older firmware, this accidentally worked to some degree due to missing
checks, but couldn't be supported properly, because it left the 6 GHz
channels uncalibrated.
Newer firmware refuses to start on either band if the passed EEPROM
data indicates support for both.
Deal with this limitation by using a module parameter to specify the
preferred band in case both are supported.
Fixes: b4d093e321bd ("mt76: mt7915: add 6 GHz support")
Cc: [email protected]
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The need to retry a command is really uncommon. Reduce the retries to 1 to
speed up recovery from firmware issues.
Signed-off-by: Felix Fietkau <[email protected]>
commit c4f075582304 ("wifi: mt76: mt7915: fix command timeout in AP stop
period") changes the behavior of mt7915_bss_info_changed() in mesh mode
when enable_beacon becomes false: it calls mt7915_mcu_add_bss_info(...,
false) and mt7915_mcu_add_sta(..., false) while the previous code
didn't. These sends mcu commands that apparently confuse the firmware.
This breaks scanning while in mesh mode on AsiaRF MT7916 DBDC-based cards:
scanning works but no mesh frames get sent afterwards and the firmware
seems to be hosed. It breaks on MT7916 DBDC but not on MT7915 DBDC.
Fixes: c4f075582304 ("wifi: mt76: mt7915: fix command timeout in AP stop period")
Signed-off-by: Nicolas Cavallari <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Do not trigger full restarts when running into timeouts during SER.
Immediately abort MCU commands when firmware requests DMA restart.
Signed-off-by: Felix Fietkau <[email protected]>
- use reconfig_complete to restart mac_work / queues
- reset full wtbl after firmware init
- clear wcid and vif mask to avoid leak
Signed-off-by: Felix Fietkau <[email protected]>
When ieee80211_restart_hw is called, all interfaces and stations are
recreated. This can lead to corruption in the sta poll list, since
existing entries were not removed before their private data is reset.
Signed-off-by: Felix Fietkau <[email protected]>
On MT7915, MCU hangs do not trigger watchdog interrupts, so they can only
be detected through MCU message timeouts. Ensure that the hardware gets
restarted when that happens in order to prevent a permanent stuck state.
Signed-off-by: Felix Fietkau <[email protected]>
In some cases MCU messages can get lost. Instead of failing completely,
attempt to recover by re-sending them.
Signed-off-by: Felix Fietkau <[email protected]>
This allows the core code to change the channel. Code deduplication and
preparation for adding scanning code to the core.
Signed-off-by: Felix Fietkau <[email protected]>
Currently, CONNAC2 series do not support encryption for fragmented Tx frames.
Therefore, add dummy function mt7915_set_frag_threshold() to prevent SW
IEEE 802.11 fragmentation.
Signed-off-by: Benjamin Lin <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
of_gpio.h is deprecated and subject to remove.
The driver doesn't use it, simply remove the unused header.
Signed-off-by: Andy Shevchenko <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix the following sparse warnings:
drivers/net/wireless/mediatek/mt76/mt7915/debugfs.c:1133:29: error: too long token expansion
drivers/net/wireless/mediatek/mt76/mt7915/debugfs.c:1133:29: error: too long token expansion
drivers/net/wireless/mediatek/mt76/mt7915/debugfs.c:1133:29: error: too long token expansion
drivers/net/wireless/mediatek/mt76/mt7915/debugfs.c:1133:29: error: too long token expansion
No functional changes, compile tested only.
Fixes: e3296759f347 ("wifi: mt76: mt7915: enable per bandwidth power limit support")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Acked-by: Felix Fietkau <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Link: https://msgid.link/5457b92e41909dd75ab3db7a0e9ec372b917a386.1710858172.git.lorenzo@kernel.org
When pre-calibration data is missing, do not fail the driver probe.
Instead, just print a warning and fall back to regular calibration.
Signed-off-by: Felix Fietkau <[email protected]>
Add pre-calibration for mt7986 and mt7916. It has different data size
with mt7915. Group cal needs 54k and 94k for 2G + 5G and 2G + 6G,
respectively. DPD cal needs 300k.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: StanleyYP Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Send an update to the MCU whenever the settings change
Signed-off-by: MeiChia Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Set correct beamformer capabilities for station vif in HE PHY
capabilities IE.
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Do not report measurements if the airtime counter was cleared since the
last update (possibly by firmware)
Signed-off-by: Henry Yen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The mcu command format are different for mt7915 and mt7986.
Fix the mt7915_mcu_wed_wa_tx_stats to support mt7915 and mt7986.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce wed.c in order to collect mt76 wed common codebase used by
mt7915 and mt7996 drivers.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Sicne the mapping is global, mapped register access needs to be protected
against concurrent access, otherwise a race condition might cause the reads
or writes to go towards the wrong register
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Do not clear the interrupt mask register on MT7915, since that prevents
MCU_CMD interrupts from being reported, thus causing timeouts during the
reset sequence. Defer stopping WED until tx/rx processing activity has
stopped.
Signed-off-by: Felix Fietkau <[email protected]>
Just like MT7916 also MT7981 can handle 3T3R DBDC frontend and should
hence be included in the corresponding conditional expression in the
driver. Add it.
Fixes: 6bad146d162e ("wifi: mt76: mt7915: add support for MT7981")
Signed-off-by: StanleyYP Wang <[email protected]>
Signed-off-by: Daniel Golle <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The offset of the TSSI flag on the EEPROM of MT7981 devices was wrong.
Set the correct offset instead.
Fixes: 6bad146d162e ("wifi: mt76: mt7915: add support for MT7981")
Signed-off-by: StanleyYP Wang <[email protected]>
Signed-off-by: Daniel Golle <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The power gain value is related to total TX path, so change the
calculation to use per-phy chainmask.
Signed-off-by: Allen Ye <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use per-phy structure for maximum txpower value initializing, since each
phy may have a different chainmask, which can impact the calculation of
power gain.
Co-developed-by: Allen Ye <[email protected]>
Signed-off-by: Allen Ye <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt76 assumes mt7915_mmio_wed_init can fail just after wed driver has
been attached running mtk_wed_device_attach().
Fall back to non-wed mode if platform_get_resource fails in
mt7915_mmio_wed_init routines.
Fixes: eebb70976be5 ("wifi: mt76: mt7915: enable wed for mt7986-wmac chipset")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move WED reset code shared between mt7915 and mt7996 in common module.
This is a preliminary patch to introduce WED reset support for mt7996.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Felix Fietkau