mt76u_alloc_queues need to be called before mt76u_mcu_init_rx
since it initializes rx_page_lock spinlock used in mt76u_buf_alloc
routine.
Fixes: b11e19694dc9 ("mt76x0: add ieee80211_ops ops pointer to
mt76x0_alloc_device signature")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add mt76x0e_cleanup routine to tidy up the device
during device removal
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76x0u_tx_prepare_skb routine in usb module in
order to remove leftover usb dependency from generic code
Signed-off-by: Lorenzo Bianconi <[email protected]>
Introduce mt76x0e_start and mt76x0e_stop mac80211
callbacks to start/stop device mac opening/closing
the netdevice
Signed-off-by: Lorenzo Bianconi <[email protected]>
Add ieee80211_ops ops pointer to mt76x0_alloc_device routine signature
in order to specify mac80211 callbacks and remove usb dependency from
mt76x0 generic code.
Move mt76x0_ops callbacks in usb module in order to remove leftover
usb dependency in mt76x0 generic code.
Introduce mt76x0e_ops mac80211 callbacks for pci code
Signed-off-by: Lorenzo Bianconi <[email protected]>
Move mt76x02_phy_set_rxpath and mt76x02_phy_tx_dac routines in
mt76x02_phy.c since they are shared between mt76x2 and mt76x0 drivers.
Moreover move chainmask variable from mt76x2/mt76x0 to mt76_dev data
structure
Signed-off-by: Lorenzo Bianconi <[email protected]>
Move mt76x0_ant_select routine in __mt76x0_phy_set_channel in order to
configure antenna parameters according to the current wireless channel
Signed-off-by: Lorenzo Bianconi <[email protected]>
Move usb initialization code in mt76x0-usb module in
order to remove usb dependency from generic init code
(not completed yet). Moreover fix a memory leak in usb probe
if mt76x02_wait_for_mac fails
Signed-off-by: Lorenzo Bianconi <[email protected]>
Initialize rxfilter mask at bootstrap an not at mac start.
This is a preliminary patch to share mt76x2_mac_start routine
between mt76x2e and mt76x0e drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Remove MT_PBF_SYS_CTRL configuration in mt76x0_reset_csr_bbp since
it is already initialized in mt76x0_init_mac_registers routine
Signed-off-by: Lorenzo Bianconi <[email protected]>
Remove MT_HEADER_TRANS_CTRL_REG/MT_TSO_CTRL configuration
since they are already initialized in mt76x0_init_mac_registers
routine
Signed-off-by: Lorenzo Bianconi <[email protected]>
Use mt76x02_wait_for_wpdma and mt76x02_wait_for_txrx_idle
utility routines in mt76x0_init_hardware and mt76x0_mac_start
and remove duplicated code
Signed-off-by: Lorenzo Bianconi <[email protected]>
Move usb mcu code in a dedicated source file in order to remove
usb dependency from generic source files and improve code
maintainability
Signed-off-by: Lorenzo Bianconi <[email protected]>
Move pci mcu code in a dedicated source file in order to
improve maintainability and facilitate new device support
development
Signed-off-by: Lorenzo Bianconi <[email protected]>
Move mt76x02_beacon_offset utility routine in mt76x02-lib module
since it is shared between mt76x0 and mt76x2 driver and remove
duplicated code. Moreover move beacon_offset data structure in
mt76x02-lib module since it is shared between mt76x0 and mt76x2
drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
TP-LINK Archer T1U do not support 2.4GHz band despite EEPROM
reports that. Add quirk to mask out 2.4GHz support.
Reported-by: Sid Hayn <[email protected]>
Signed-off-by: Stanislaw Gruszka <[email protected]>
print fw_ver and build_ver members of struct mt76x02_fw_header, similarly
to what appears in the output of 'dmesg' when the MCU firmware is loaded.
Reported-by: Sid Hayn <[email protected]>
Signed-off-by: Davide Caratti <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add mt76x0_phy_set_txpower routine in order to configure
base and per rate tx power gain. Moreover take into account
txpower_conf in order to limit the tx power gain according to
the bound provided by mac80211
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use mt76 shared debugfs implementation and remove duplicated code
in mt76x0 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In order to unify eeprom parsing between mt76x0 and mt76x2 drivers,
remove eeprom pointer dependency from mt76x0_get_power_info routine.
Remove mt76x0_eeprom_params since it is now an empty structure
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In order to unify eeprom parsing between mt76x0 and mt76x2 drivers,
remove eeprom pointer dependency from mt76x0_set_tx_power_per_rate.
Moreover use mt76_rate_power to store power vs rate calibration data.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove mt76x0_extra_power_over_mac and mt76x0_phy_set_tx_power routines
since they are not actually used and tx power handling will be unified
with mt76x2 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Unify parse hw capabilities with mt76x2 driver using
mt76x02_eeprom_parse_hw_cap utility routine available
in mt76x02-lib module
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Unify frequency offset parsing with mt76x2 driver using
eeprom utility routines available in mt76x02-lib module
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Unify temperature offset parsing with mt76x2 driver using
eeprom utility routines available in mt76x02-lib module
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Unify rssi_offset parsing with mt76x2 driver using eeprom utility
routines available in mt76x02-lib module
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Unify lna gain parsing with mt76x2 driver using eeprom utility
routines available in mt76x02-lib module
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove mt76x0_set_country_reg routine for the moment
since it is partial and it is not actually used
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76x2_ext_pa_enabled utility routine in mt76x02_eeprom.c
and remove duplicated code. This is a preliminary patch to
unify eeprom code between mt76x2 and mt76x0 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76x2_efuse_read and mt76x2_get_efuse_data in mt76x02_eeprom.c
in order to be reused in mt76x0 driver for eeprom parsing
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76x02_mac_setaddr utility routine in mt76x02-lib
module and remove duplicated code. This is a preliminary patch
to unify eeprom code between mt76x2 and mt76x0 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76x2 and mt76x0 common definitions in mt76x02_eeprom.h
and remove duplicated code
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add mt7650 PCI id found on ASUS rt-51ac to pci_device_id table
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove mt76_fw dependency from mt76x0u_upload_firmware routine since
it does not define firmware layout properly. Moreover use mt76_poll_msec
utility routine to check if the fw is properly running
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove unused usb header file and move mt76x0 firmware definition
in usb.c
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove mcu.c source file since it contains just 'one-line' function
that is shared between PCI and USB code
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Firmware loading is usb specific, move it to usb.c file.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mcu_calibrate routine in mt76x02-lib module since it is
shared between USB and PCI code. Moreover remove duplicated
code
Signed-off-by: Lorenzo Bianconi <[email protected]>
Remove mt76_mcu_msg_alloc return value check since it is already
evaluated in __mt76x02u_mcu_send_msg
Signed-off-by: Lorenzo Bianconi <[email protected]>
