This allows the core code to change the channel. Code deduplication and
preparation for adding scanning code to the core.
Signed-off-by: Felix Fietkau <[email protected]>
Use the correct ieee80211_conf of each band for IEEE80211_CONF_MONITOR
comparison.
Fixes: 24e69f6bc3ca ("mt76: fix monitor rx FCS error in DFS channel")
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mcu_uni_event and mcu_reg_event structs are shared between mt7921 and
mt7615 drivers, so move them in connac lib.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce p2p-go/p2p-client support to mt7921 driver
CONNECTION_P2P_GC/GO is not supported with the current firmware
so we added mt76_dev to mt76_connac_mcu_sta_basic_tlv signature to
use CONNECTION_INFRA_STA/AP instead for p2p-client and p2p-go
respectively to make it work.
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Run mt7615_mcu_restart routine directly and avoid mcu_restart function
pointer whenever it is possible.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add a chanctx parameter to mt76_connac_mcu_uni_add_bss signature to allow
the firmware binds the BSS into the specific channel context.
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Report phy_indx in tx_info->hw_queue. This is a preliminary patch to add
newer chipset support
Co-developed-by: Bo Jiao <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Introduce phys array in mt76_dev structure to reference mt76_phy
supported by the chipset. This is a preliminary patch to introduce
newer chipset support.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Previously the code used skb_set_queue_mapping for management or non-bufferable
powersave frames that need to be sent to a different hardware queue.
This can confuse AQL, which expects the value to remain the same until the tx
status report.
The only place that currently uses the altered skb queue mapping is the txwi
write function. Change the code to pass the hardware queue id as a function
parameter instead.
Signed-off-by: Felix Fietkau <[email protected]>
For some reason, mt7615 reacts badly to repeatedly enabling/disabling the radar
detector without also switching the channel.
This results in very bad throughput on DFS channels, because
hw->conf.radar_enabled can get toggled a few times after CAC ends.
Fix this by always leaving the DFS detector enabled on DFS channels and instead
suppress unwanted detection events.
Fixes: 2c86f6752046 ("mt76: mt7615: fix/rewrite the dfs state handling logic")
Signed-off-by: Felix Fietkau <[email protected]>
Set EXTRA_INFO_NEW for the first time only to prevent adding the same
starec entry, otherwise the entry might be removed in fw.
Signed-off-by: Felix Fietkau <[email protected]>
Do not update pm stats if mt7615_mcu_fw_pmctrl returns an error.
Fixes: abe912ae3cd42 ("mt76: mt7663: add awake and doze time accounting")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When setup monitor mode in DFS channel, mt76 send CH_SWITCH_DFS to
fw for channel config. This would cause rx performance bad while
monitoring frames. Settings CH_SWITCH_NORMAL in monitor mode would
get the same performance as normal channels.
Reviewed-by: Shayne Chen <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The original single LDPC cap bit cannot be used to
differentiate LDPC cap in each PHY mode.
This modification split the single bit into 3 bits,
ht_ldpc, vht_ldpc, and he_ldpc.
Reviewed-by: Ryder Lee <[email protected]>
Suggested-by: Money Wang <[email protected]>
Signed-off-by: MeiChia Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When operating on a mix of DFS and non-DFS channels, the driver only checks
the CAC status of the control channel. This causes beacons/tx to fail if the
control channel is on a non-DFS channel.
Fix this by calling cfg80211_reg_can_beacon to determine the DFS status of
all affected channels
Signed-off-by: Felix Fietkau <[email protected]>
Add SAR spec support to mt7615 driver to allow configuring SAR power
limitations on the frequency ranges from the userland.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_connac_mcu_rdd_cmd routine in mt76-connac module and remove
duplicated code.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_connac_mcu_gen_dl_mode utility routine in mt76_connac_mcu.h
since it is shared by all drivers.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_connac_mcu_set_pm utility routine in connac module since it is
shared between mt7615 and mt7915 drivers.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_connac_mcu_wtbl_update_hdr_trans routine in mt76-connac module
since it is shared between mt7915 and mt7615 drivers.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rely on mt76_connac_mcu_wtbl_ht_tlv routine and
remove duplicated code.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rely on mt76_connac_mcu_sta_ba routine in mt7915 and remove duplicated
code.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt7615_mcu_bss_basic_tlv/mt7915_mcu_bss_basic_tlv in connac
module since it is shared between mt7615 and mt7915 drivers.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt7915_mcu_bss_ext_tlv/mt7615_mcu_bss_ext_tlv in connac module
since it is shared between mt7615 and mt7915 drivers.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt7915_mcu_bss_omac_tlv/mt7615_mcu_bss_omac_tlv in connac module
since it is shared between mt7615 and mt7915 drivers.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Similar to mt7915 driver, rely on MCU_CMD macro and do not command
definitions directly
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Similar to MCU_EXT_CMD, introduce MCU_CE_CMD for CE commands
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Similar to MCU_EXT_CMD, introduce MCU_UNI_CMD for unified commands
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Align MCU_EXT and MCU_FW definitions between mt76_connac and mt7915
driver. This is a preliminary patch to reuse mt76_connac in mt7915
driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce MCU_EXT_CMD and MCU_EXT_QUERY macros in mt76_connac module.
This is a preliminary patch to reuse mt76_connac module in mt7915
driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Band0 and band1 share the same hardware, so band0 will stop Tx/Rx when
band1 performs Rx calibration. cal_cache is introduced to solve such
corner cases by moving necessary datas from channel_switch to bootup.
Co-developed-by: Peter Chiu <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt7615_mcu_set_p2p_oppps routine in mt76_connac_lib module in order
to be reused in mt7921 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When .sta_state is implemented, mac80211 assumes that the station entry is
usable after the NOTEXIST->NONE transition.
So we should create the sta entry as early as possible in order that
mac80211 pass assoc/auth frames to mt76 with the newly created sta entry,
and add .sta_assoc to mt76 core to refresh the sta entry again when sta is
being associated.
Fixes: 8aa5a9b7361c ("mt76: mt7921: enable deep sleep at runtime")
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Patch radar parameters to match the SDK to avoid possible false alarms.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Similar to mt7915, switching to use standard hwmon sysfs.
For reading temperature, cat /sys/class/ieee80211/phy*/hwmon*/temp1_input
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
As already done for mt7615 and mt7915, enable rx header translation
offload for mt7663 in order to reduce cpu load in the rx path.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Precision "%.*s" was intended instead of width "%*s". The original code
will print garbage from beyond the end of the skb->data.
Fixes: d76d6c3ba2b0 ("mt76: mt7615: limit firmware log message printk to buffer length")
Signed-off-by: Dan Carpenter <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Similar to mt7921, introduce awake and doze time accounting
for runtime pm.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In order to avoid synchronization races between tx and rx path, rely on
mt76_connac_skip_fw_pmctrl putting the chip in sleep mode for mt7921 and
mt7663 devices
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
