Also report auth/disassoc events, in order to give the driver more control over
handling the station state.
Signed-off-by: Felix Fietkau <[email protected]>
This allows the core code to change the channel. Code deduplication and
preparation for adding scanning code to the core.
Signed-off-by: Felix Fietkau <[email protected]>
Move the qid variable declaration further up
Fixes: b473c0e47f04 ("wifi: mt76: mt7603: fix tx queue of loopback packets")
Signed-off-by: Felix Fietkau <[email protected]>
This flag is needed for the PSE client reset. Fixes watchdog reset issues.
Fixes: c677dda16523 ("wifi: mt76: mt7603: improve watchdog reset reliablity")
Signed-off-by: Felix Fietkau <[email protected]>
Use the correct WMM AC queue instead of the MGMT one to fix potential issues
with aggregation sequence number tracking. Drop non-bufferable packets.
Fixes: fca9615f1a43 ("mt76: mt7603: fix up hardware queue index for PS filtered packets")
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mtk_wed_device pointer in mt76_queue structure in order to
configure WED chip.
Get rid of dev parameter in Q_READ and Q_WRITE macros.
Introduce wed parameter to the following routine signatures:
- mt76_init_queue
- mt76_init_tx_queue
This is a preliminary patch to introduce WED support for mt7996 since
mt7996 runs two separate WED chips.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Before preparing the new beacon, check the queue status, flush out all
previous beacons and buffered multicast packets, then (if necessary)
try to recover more gracefully from a stuck beacon condition by making a
less invasive attempt at getting the MAC un-stuck.
Fixes: c8846e101502 ("mt76: add driver for MT7603E and MT7628/7688")
Signed-off-by: Felix Fietkau <[email protected]>
Only trigger PSE reset if PSE was stuck, otherwise it can cause DMA issues.
Trigger the PSE reset while DMA is fully stopped in order to improve
reliabilty.
Fixes: c8846e101502 ("mt76: add driver for MT7603E and MT7628/7688")
Signed-off-by: Felix Fietkau <[email protected]>
It turns out that the code in mt7603_rx_pse_busy() does not detect actual
hardware hangs, it only checks for busy conditions in PSE.
A reset should only be performed if these conditions are true and if there
is no rx activity as well.
Reset the counter whenever a rx interrupt occurs. In order to also deal with
a fully loaded CPU that leaves interrupts disabled with continuous NAPI
polling, also check for pending rx interrupts in the function itself.
Fixes: c8846e101502 ("mt76: add driver for MT7603E and MT7628/7688")
Signed-off-by: Felix Fietkau <[email protected]>
Setting MT_TX_ABORT does not abort any transmission for a wtbl index on its
own. Instead, it modifies the behavior of a queue flush to make it selectively
flush packets for a particular wtbl index.
Adjust powersave filtering to make use of this in order to avoid running into
unnecessary timeouts while flushing
Signed-off-by: Felix Fietkau <[email protected]>
When disabling beacons on a vif, intval is 0. Ensure that dev->mt76.beacon_int
is not overwritten in this case, so that beacons continue to work for other
interfaces.
Signed-off-by: Felix Fietkau <[email protected]>
Rely on poll_list field in mt76_wcid structure and get rid of
private copy.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rely on sta_poll_list and sta_poll_lock fields in mt76_dev structure
and get rid of private copies.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
According to the documentation, ieee80211_rx_list must not run concurrently
with ieee80211_tx_status (or its variants).
Cc: [email protected]
Fixes: 88046b2c9f6d ("mt76: add support for reporting tx status with skb")
Reported-by: Brian Coverstone <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This helps avoid cleartext leakage of already queued or powersave buffered
packets, when a reassoc triggers the key deletion.
Cc: [email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Run mt7603_mcu_restart routine directly and avoid mcu_restart function
pointer whenever it is possible.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move leds struct in mt76_phy in order to have leds associated to phy
(e.g. in dbdc mode) instead of per device.
Tested-by: Frank Wunderlich <[email protected]>
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move aggregation stats array per-phy instead of share it between multiple
interfaces. This is a preliminary patch to add mt7996 driver support.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
MT7915_MAX_INTERFACES is per-band declaration in MT7915/MT7986/MT7916.
Enlarge vif_mask to 64 bits wide, including the bit operation.
Reviewed-by: Shayne Chen <[email protected]>
Signed-off-by: Evelyn Tsai <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Switch to use le32/16_get_bits() to simplfy codes and specify
the size explicitly to avoid potential issues.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Instead of just taking the maximum per-chain signal strength values,
add an approximation for the sum of the combined signal.
This should more accurately reflect the real signal strength, especially
if the per-chain signal strength values are close to each other
Signed-off-by: Felix Fietkau <[email protected]>
Check sta_rates pointer value in mt7603_sta_rate_tbl_update routine
since minstrel_ht_update_rates can fail allocating rates array.
Fixes: c8846e1015022 ("mt76: add driver for MT7603E and MT7628/7688")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Leave more time to abort transmissions (which could happen at low CCK rates)
Only warn if the last filter command is stuck
Signed-off-by: Felix Fietkau <[email protected]>
Add SAR spec support to mt7603 driver to allow configuring SAR power
limitations on the frequency ranges from the userland.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
MAC80211 doesn't care any decryption error in 802.3 path, so received
frame will be dropped if HW tell us that the cipher configuration is not
matched as well as the header has been translated to 802.3. This case only
appears when IEEE80211_FCTL_PROTECTED is 0 and cipher suit is not none in
the corresponding HW entry.
The received frame is only reported to monitor interface if HW decryption
block tell us there is ICV error or CCMP/BIP/WPI MIC error. Note in this
case the reported frame is decrypted 802.11 frame and the payload may be
malformed due to mismatched key.
Signed-off-by: Xing Song <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove mt76_wcid pointer from mt76_tx_status_check signature since it is
always set to NULL
Tested-by: [email protected]
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce per-wcid idr to manage packet id for txs. This allow fast idr
lookup and skb queueing at the same time.
Tested-by: [email protected]
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
napi_schedule() can call __raise_softirq_irqoff(), which can perform softirq
handling, so it must not be called in a pure process context with BH enabled.
Signed-off-by: Felix Fietkau <[email protected]>
PHY offset in either .hw_value or .hw_value_short for mt7615, mt7663,
mt7915 and mt7921 device all start at bit 6, not 8.
Suggested-by: Ryder Lee <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The iv from RXD is only for TKIP_RSC/CCMP_PN/GCMP_PN, and it needs a
check for CCMP header insertion. Move mt76_cipher_type to mt76.h to
reduce duplicated code.
Signed-off-by: Xing Song <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add the capability to define a custom rx napi callback for each driver.
This is a preliminary patch to properly support runtime-pm on rx side
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Dump mcu command code in hex and related prefix to help debugging
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Felix Fietkau