- use reconfig_complete to restart mac_work / queues
- reset full wtbl after firmware init
- clear wcid and vif mask to avoid leak
Signed-off-by: Felix Fietkau <[email protected]>
- initialize and use per-sta wcid entry instead of vif wcid
- set wcid flags for 4addr/offload
- fix 'newly' argument for vif sta entry update
Signed-off-by: Felix Fietkau <[email protected]>
On MT7915, MCU hangs do not trigger watchdog interrupts, so they can only
be detected through MCU message timeouts. Ensure that the hardware gets
restarted when that happens in order to prevent a permanent stuck state.
Signed-off-by: Felix Fietkau <[email protected]>
In some cases MCU messages can get lost. Instead of failing completely,
attempt to recover by re-sending them.
Signed-off-by: Felix Fietkau <[email protected]>
This allows the core code to change the channel. Code deduplication and
preparation for adding scanning code to the core.
Signed-off-by: Felix Fietkau <[email protected]>
Add pre-calibration for mt7986 and mt7916. It has different data size
with mt7915. Group cal needs 54k and 94k for 2G + 5G and 2G + 6G,
respectively. DPD cal needs 300k.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: StanleyYP Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Send an update to the MCU whenever the settings change
Signed-off-by: MeiChia Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The mcu command format are different for mt7915 and mt7986.
Fix the mt7915_mcu_wed_wa_tx_stats to support mt7915 and mt7986.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Without this patch, when ap sets the tx stream number to 2,
ap won't send any beamforming packet.
Fixes: f89f297aef28 ("mt76: mt7915: fix txbf starec TLV issues")
Signed-off-by: MeiChia Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Do not report cca and csa finish to upper layer on station type vif to
prevent warnings caused by setting beacon.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use the correct ieee80211_conf of each band for IEEE80211_CONF_MONITOR
comparison.
Fixes: 24e69f6bc3ca ("mt76: fix monitor rx FCS error in DFS channel")
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When the set_chan_info command is set with CH_SWITCH_NORMAL reason,
even if the action is UNI_CHANNEL_RX_PATH, it'll still generate some
unexpected tones, which might confuse DFS CAC tests that there are some
tone leakages. To get rid of these kinds of false alarms, always bypass
DPD calibration when IEEE80211_CONF_IDLE is set.
Reviewed-by: Evelyn Tsai <[email protected]>
Signed-off-by: StanleyYP Wang <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add CAP3_RX_CTRL_FRAME_TO_MULTIBSS check when setting sta_muru_tlv,
which is used to get stations's capability of receiving control frames
when running OFDMA with MBSSIDs.
Signed-off-by: Allen Ye <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Correct per-device TLV lengths to avoid invalid operation in firmware.
( 64.040375:28:STATS-E)statsGetSingleHWCounter: MIB counter index = 65472 not supported.
This happens on mt7916/mt7986.
Fixes: b0bfa00595be ("wifi: mt76: mt7915: improve accuracy of time_busy calculation")
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Capabilities in vif->bss_conf are only initialized in AP mode.
For other modes, they should be enabled by default, in order to avoid a
mismatch.
Fixes: 885f7af7e544 ("wifi: mt76: mt7915: remove mt7915_mcu_beacon_check_caps()")
Signed-off-by: Felix Fietkau <[email protected]>
The stats are clear-on-read, which makes it very difficult for tools
to adequately deal with wrapped stats and with keeping good totals.
So, accumulate these values when they are read from the firmware/radio
and present totals to user-space.
Signed-off-by: Ben Greear <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
PPDU TxS can only report MPDU count whereas mac80211 requires MSDU scale
(NL80211_STA_INFO_TX_PACKETS), so switch to get MSDU counts from WA
statistic.
Note that mt7915 WA firmware only counts tx_packet for WED path, so driver
needs to take care of host path additionally.
Fixes: 43eaa3689507 ("wifi: mt76: add PPDU based TxS support for WED device")
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The background radar uses MT_RX_SEL2 as its band indication, so fix it.
Fixes: 7a53eecd5c87 (wifi: mt76: mt7915: check the correctness of event data)
Signed-off-by: StanleyYP Wang <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add support for the MediaTek MT7981 SoC which is similar to the MT7986
but with a newer IP cores and only 2x ARM Cortex-A53 instead of 4x.
Unlike MT7986 the MT7981 can only connect a single wireless frontend,
usually MT7976 is used for DBDC.
Signed-off-by: Alexander Couzens <[email protected]>
Signed-off-by: Daniel Golle <[email protected]>
Introduce p2p-go/p2p-client support to mt7921 driver
CONNECTION_P2P_GC/GO is not supported with the current firmware
so we added mt76_dev to mt76_connac_mcu_sta_basic_tlv signature to
use CONNECTION_INFRA_STA/AP instead for p2p-client and p2p-go
respectively to make it work.
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Those capabilities have been added into ieee80211_bss_conf.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Enable two PCIe interfaces (dev->hif2) support for mt7916 when WED is enabled.
Signed-off-by: Sujuan Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Enable RED to limit the number of token used by each band. If single band
uses too many tokens, it would hurt the throughput of the other bands.The
software path can solve this problem by AQL so enable RED for HW path only.
Reviewed-by: Shayne Chen <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Run mt76_connac_mcu_restart routine directly and avoid mcu_restart
function pointer whenever it is possible.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This patch includes 2 changes:
1. Firmware expects to disable thermal protect first before
reconfiguring.
2. Separate setting thermal_protect and setting thermal_tx_duty into
different functions. These two firmware commands do not need to send
together.
Fixes: 34b877d972be ("mt76: mt7915: add thermal cooling device support")
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The mcu event might not be reliable, so check the correctness of data
before handling it.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Check return value of mt7915_mcu_get_eeprom_free_block() first before
accessing free_block_num.
Fixes: bbc1d4154ec1 ("mt76: mt7915: add default calibrated data support")
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The current flow confuses coverity check that leads to false reporting,
so split the offs[] into two pieces according to chipset revision to
silence coverity tool.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The commit dc44c45c8cd0 added band_idx into mt76_phy, so switching to
rely on that.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Firmware is in the driving seat while sr_scene_detect is enabled,
so driver needs to skip operation to avoid mangling scene detection
algorithm.
Fixes: a633503 ("wifi: mt76: mt7915: add support to configure spatial reuse parameter set")
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This power should override the per bandwidth max power that the
device emits.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add a helper for common boundary check. This is a preliminary patch
to add per bandwidth power control.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix sparse: sparse: incorrect type in assignment (different base types).
Fixes: a6335031eb96 ("wifi: mt76: mt7915: add support to configure spatial reuse parameter set")
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The commit 006b9d4ad5bf introduced phy->band_idx to accommodate the
band definition change for mt7986 so that the band_idx of main_phy
can be 0 or 1. Accordingly, the source of band_idx 1 has switched to
"phy != &dev->phy" or "dev->phy.band_idx = 1".
We still use ext_phy to represent band 1 somewhere in driver, so fix it.
Also, band_idx sounds more reasonable than dbdc_idx, so change it.
Fixes: 006b9d4ad5bf ("mt76: mt7915: introduce band_idx in mt7915_phy")
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Felix Fietkau