- use reconfig_complete to restart mac_work / queues
- reset full wtbl after firmware init
- clear wcid and vif mask to avoid leak
Signed-off-by: Felix Fietkau <[email protected]>
- initialize and use per-sta wcid entry instead of vif wcid
- set wcid flags for 4addr/offload
- fix 'newly' argument for vif sta entry update
Signed-off-by: Felix Fietkau <[email protected]>
This allows the core code to change the channel. Code deduplication and
preparation for adding scanning code to the core.
Signed-off-by: Felix Fietkau <[email protected]>
Currently, CONNAC2 series do not support encryption for fragmented Tx frames.
Therefore, add dummy function mt7915_set_frag_threshold() to prevent SW
IEEE 802.11 fragmentation.
Signed-off-by: Benjamin Lin <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When pre-calibration data is missing, do not fail the driver probe.
Instead, just print a warning and fall back to regular calibration.
Signed-off-by: Felix Fietkau <[email protected]>
Introduce wed.c in order to collect mt76 wed common codebase used by
mt7915 and mt7996 drivers.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Just like MT7916 also MT7981 can handle 3T3R DBDC frontend and should
hence be included in the corresponding conditional expression in the
driver. Add it.
Fixes: 6bad146d162e ("wifi: mt76: mt7915: add support for MT7981")
Signed-off-by: StanleyYP Wang <[email protected]>
Signed-off-by: Daniel Golle <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce WED support for mt7996
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When compiling with clang 16.0.6 and CONFIG_FORTIFY_SOURCE=y, I've
noticed the following (somewhat confusing due to absence of an actual
source code location):
In file included from drivers/net/wireless/mediatek/mt76/mt792x_core.c:4:
In file included from ./include/linux/module.h:13:
In file included from ./include/linux/stat.h:19:
In file included from ./include/linux/time.h:60:
In file included from ./include/linux/time32.h:13:
In file included from ./include/linux/timex.h:67:
In file included from ./arch/x86/include/asm/timex.h:5:
In file included from ./arch/x86/include/asm/processor.h:23:
In file included from ./arch/x86/include/asm/msr.h:11:
In file included from ./arch/x86/include/asm/cpumask.h:5:
In file included from ./include/linux/cpumask.h:12:
In file included from ./include/linux/bitmap.h:11:
In file included from ./include/linux/string.h:254:
./include/linux/fortify-string.h:592:4: warning: call to '__read_overflow2_field'
declared with 'warning' attribute: detected read beyond size of field (2nd
parameter); maybe use struct_group()? [-Wattribute-warning]
__read_overflow2_field(q_size_field, size);
In file included from drivers/net/wireless/mediatek/mt76/mt7915/main.c:4:
In file included from ./include/linux/etherdevice.h:20:
In file included from ./include/linux/if_ether.h:19:
In file included from ./include/linux/skbuff.h:15:
In file included from ./include/linux/time.h:60:
In file included from ./include/linux/time32.h:13:
In file included from ./include/linux/timex.h:67:
In file included from ./arch/x86/include/asm/timex.h:5:
In file included from ./arch/x86/include/asm/processor.h:23:
In file included from ./arch/x86/include/asm/msr.h:11:
In file included from ./arch/x86/include/asm/cpumask.h:5:
In file included from ./include/linux/cpumask.h:12:
In file included from ./include/linux/bitmap.h:11:
In file included from ./include/linux/string.h:254:
./include/linux/fortify-string.h:592:4: warning: call to '__read_overflow2_field'
declared with 'warning' attribute: detected read beyond size of field (2nd
parameter); maybe use struct_group()? [-Wattribute-warning]
__read_overflow2_field(q_size_field, size);
In file included from drivers/net/wireless/mediatek/mt76/mt7996/main.c:6:
In file included from drivers/net/wireless/mediatek/mt76/mt7996/mt7996.h:9:
In file included from ./include/linux/interrupt.h:8:
In file included from ./include/linux/cpumask.h:12:
In file included from ./include/linux/bitmap.h:11:
In file included from ./include/linux/string.h:254:
./include/linux/fortify-string.h:592:4: warning: call to '__read_overflow2_field'
declared with 'warning' attribute: detected read beyond size of field (2nd
parameter); maybe use struct_group()? [-Wattribute-warning]
__read_overflow2_field(q_size_field, size);
The compiler actually complains on 'mt7915_get_et_strings()',
'mt792x_get_et_strings()' and 'mt7996_get_et_strings()' due to the same
reason: fortification logic inteprets call to 'memcpy()' as an attempt
to copy the whole array from its first member and so issues an overread
warning. These warnings may be silenced by passing an address of the whole
array and not the first member to 'memcpy()'.
Signed-off-by: Dmitry Antipov <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Enable receiving other-unicast packets
Disable RX header translation in order to proprerly receive data packets
Signed-off-by: Felix Fietkau <[email protected]>
If user changes the channel without completely disabling the interface the
txpower_sku values reported track the old channel the device was operating on.
If user bounces the interface the correct power tables are applied.
mt7915_sku_group_len array gets updated before the channel switch happens so it
uses data from the old channel.
Fixes: ecb187a74e18 ("mt76: mt7915: rework the flow of txpower setting")
Fixes: f1d962369d56 ("mt76: mt7915: implement HE per-rate tx power support")
Reported-By: Chad Monroe <[email protected]>
Tested-by: Chad Monroe <[email protected]>
Signed-off-by: Allen Ye <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Capabilities in vif->bss_conf are only initialized in AP mode.
For other modes, they should be enabled by default, in order to avoid a
mismatch.
Fixes: 885f7af7e544 ("wifi: mt76: mt7915: remove mt7915_mcu_beacon_check_caps()")
Signed-off-by: Felix Fietkau <[email protected]>
ampdu_state field is used by most of the drivers, so move it in
mt76_wcid structure.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
poll_list field is used by most of the drivers, so move it in mt76_wcid
structure.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
sta_poll_list and sta_poll_lock are used by most of the drivers, so move
them in mt76_dev structure.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Due to AP stop improperly, mt7915 driver would face random command timeout
by chip fw problem. Migrate AP start/stop process to .start_ap/.stop_ap and
congiure BSS network settings in both hooks.
The new flow is shown below.
* AP start
.start_ap()
configure BSS network resource
set BSS to connected state
.bss_info_changed()
enable fw beacon offload
* AP stop
.bss_info_changed()
disable fw beacon offload (skip this command)
.stop_ap()
set BSS to disconnected state (beacon offload disabled automatically)
destroy BSS network resource
Based on "mt76: mt7921: fix command timeout in AP stop period"
Signed-off-by: Rany Hany <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The stats are clear-on-read, which makes it very difficult for tools
to adequately deal with wrapped stats and with keeping good totals.
So, accumulate these values when they are read from the firmware/radio
and present totals to user-space.
Signed-off-by: Ben Greear <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mib_stats structure is shared by mostly all chipsets. Move it to shared
code.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Avoid blocking other statistics sinfo->filled when txrate is
unavailable.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
PPDU TxS can only report MPDU count whereas mac80211 requires MSDU scale
(NL80211_STA_INFO_TX_PACKETS), so switch to get MSDU counts from WA
statistic.
Note that mt7915 WA firmware only counts tx_packet for WED path, so driver
needs to take care of host path additionally.
Fixes: 43eaa3689507 ("wifi: mt76: add PPDU based TxS support for WED device")
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Get missing tx retries/failed counts from txfree done events and report
them via mt7915_sta_statistics().
Co-developed-by: Peter Chiu <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Those capabilities have been added into ieee80211_bss_conf.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This helps avoid cleartext leakage of already queued or powersave buffered
packets, when a reassoc triggers the key deletion.
Cc: [email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Add support to get EHT rate stats from ethtool.
This is the preliminary patch to add EHT support for mt7996.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This patch includes 2 changes:
1. Firmware expects to disable thermal protect first before
reconfiguring.
2. Separate setting thermal_protect and setting thermal_tx_duty into
different functions. These two firmware commands do not need to send
together.
Fixes: 34b877d972be ("mt76: mt7915: add thermal cooling device support")
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Enable thermal management by default shall not be executed during mcu
init. This causes thermal configuration being reset to the firmware
default settings.
Fixes: 0063b86c9120 ("mt76: mt7915e: Enable thermal management by default")
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Howard Hsu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The commit dc44c45c8cd0 added band_idx into mt76_phy, so switching to
rely on that.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The commit 006b9d4ad5bf introduced phy->band_idx to accommodate the
band definition change for mt7986 so that the band_idx of main_phy
can be 0 or 1. Accordingly, the source of band_idx 1 has switched to
"phy != &dev->phy" or "dev->phy.band_idx = 1".
We still use ext_phy to represent band 1 somewhere in driver, so fix it.
Also, band_idx sounds more reasonable than dbdc_idx, so change it.
Fixes: 006b9d4ad5bf ("mt76: mt7915: introduce band_idx in mt7915_phy")
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This adds support for adjusting the Txpower level while pushing
traffic to an associated station. The allowed range is from 0 to
the maximum power of channel.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The SPR parameter set comprises OBSS PD threshold for SRG and
non SRG and Bitmap of BSS color and partial BSSID. This adds
support to configure fields of SPR element to firmware.
User can disable firmware SR algorithms by turning sr_scene_detect off.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Felix Fietkau