in mt76x02_mac_process_rx(), return an error code if an
unexpected result is returned by pskb_trim.
Signed-off-by: Yuanjun Gong <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
According to the documentation, ieee80211_rx_list must not run concurrently
with ieee80211_tx_status (or its variants).
Cc: [email protected]
Fixes: 88046b2c9f6d ("mt76: add support for reporting tx status with skb")
Reported-by: Brian Coverstone <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move aggregation stats array per-phy instead of share it between multiple
interfaces. This is a preliminary patch to add mt7996 driver support.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Increment the counter only when writing beacons to the hardware in order
to avoid triggering restarts if beacons are disabled.
Additionally, avoid resetting the MAC if stopping it failed
Signed-off-by: Felix Fietkau <[email protected]>
Instead of just taking the maximum per-chain signal strength values,
add an approximation for the sum of the combined signal.
This should more accurately reflect the real signal strength, especially
if the per-chain signal strength values are close to each other
Signed-off-by: Felix Fietkau <[email protected]>
On AP mode devices, check beacon tx counters to detect MAC errors.
When an error is detected, stop the MAC before resetting it
Signed-off-by: Felix Fietkau <[email protected]>
Remove mt76_wcid pointer from mt76_tx_status_check signature since it is
always set to NULL
Tested-by: [email protected]
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix the following sparse warning in mt76x02_mac_write_txwi and
mt76x02_mac_tx_rate_val routines:
drivers/net/wireless/mediatek/mt76/mt76x02_mac.c:237:19:
warning: restricted __le16 degrades to intege
warning: cast from restricted __le16
drivers/net/wireless/mediatek/mt76/mt76x02_mac.c:383:28:
warning: incorrect type in assignment (different base types)
expected restricted __le16 [usertype] rate
got unsigned long
Fixes: db9f11d3433f7 ("mt76: store wcid tx rate info in one u32 reduce locking")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The iv from RXD is only for TKIP_RSC/CCMP_PN/GCMP_PN, and it needs a
check for CCMP header insertion. Move mt76_cipher_type to mt76.h to
reduce duplicated code.
Signed-off-by: Xing Song <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move chainmask from driver phy to mt76_phy since it is used by all
drivers. This is a preliminary patch to create a common mcu library used
by mt7615 and mt7921 drivers
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mac_work delayed_work and mac_work_count in mt76_phy since it is
used by all drivers. This is a preliminary patch to create a common mcu
library used by mt7615 and mt7921 drivers
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to properly support mt7915 dbdc
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Now that AQL works well on all mt76 drivers, completely replace the arbitrary
burst sizing and number of bursts logic for tx scheduling.
For the short period of time in which AQL does not work well yet, limit each
stations to 16 in-flight packets that have no estimated tx time.
This should avoid filling the queue if a station connects and queues up a
large number of packets before rate control information is available, especially
with hardware rate control
Signed-off-by: Felix Fietkau <[email protected]>
mt7615 and newer drivers do not need this, since they use sequence number offload
Moving this code also reduces the number of callsites to make it easier to review
Signed-off-by: Felix Fietkau <[email protected]>
All drivers before MT7915 have a limit of 128 WCID entries. Stop relying
on ARRAY_SIZE(dev->mt76.wcid), since it no longer reflects that limit.
Fixes: 49e649c3e0a6 ("mt76: adjust wcid size to support new 802.11ax generation")
Reported-by: kbuild test robot <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The hardware requirements for A-MPDU density are entirely on the tx side,
not the rx side. Because of that, the IE value should stay at 0 and the
minimum value should instead be enforced in WTBL/TXWI
MT7615 has no restrictions here
Signed-off-by: Felix Fietkau <[email protected]>
Move mac_txdone tracepoint in common code in order to
be reused by mt7603 and mt7615 drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Sending beacons to the hardware always happens in batches. In order to
speed up beacon processing on usb devices, this patch splits out common
code an calls it only once.
Beacons are sequentially written into the beacon memory area, by
tracking its usage with the dev->beacon_data_count. For MBSS support
and buffered traffic dev->beacon_data_count is used to create the bypass
mask.
The code is also adapted for the mmio part of the driver, but should not
have any performance implication there.
MBSS tests were performed with AVM AC860 USB NIC with temporary support
for 5 BSS'. Different combinations of active vifs were created and
brought up. Afterwards connection and data transfer was tested for the
announced BSS'.
Signed-off-by: Markus Theil <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add support for an extra wiphy in mt76_set_channel and mt76_get_survey
This is preparation for supporting multiple wiphys per device to support the
concurrent dual-band feature of MT7615D
Signed-off-by: Felix Fietkau <[email protected]>
status.info could point to skb->cb, leading to a use-after-free after the tx
status has been reported to mac80211
Signed-off-by: Felix Fietkau <[email protected]>
Host time is used to calculate the channel active time on mt7603 and mt7615.
Use the same on mt76x02 and move the lock to core code to get rid of some
duplicated code.
Signed-off-by: Felix Fietkau <[email protected]>
Report total rx airtime for valid stations as BSS rx time in survey
mt7615 is left out for now, it will be supported later by reading
hardware counters instead of calculating airtime in software
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_channel_state() from mt76.h to mac80211.c
Preparation for updating channel state from more places in the drivers/core
Signed-off-by: Felix Fietkau <[email protected]>
Move aggr_stats array from mt76x02_dev to mt76_dev in order to be reused
adding aggregation stats for mt7603/mt7615 drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Unify mac_reset_counter routine and move it in mt76x02_lib module
since it is shared by all mt76x02 drivers (pci/usb)
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
No functional change intended.
Add SPDX identifiers to all remaining files in /mt76.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This fixes the following checkpatch warnings:
ERROR: code indent should use tabs where possible
CHECK: Alignment should match open parenthesis
CHECK: No space is necessary after a cast
CHECK: Please don't use multiple blank lines
CHECK: Avoid precedence issues in macro
WARNING: Statements should start on a tabstop
WARNING: Unnecessary space before function pointer arguments
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove enable parameter from mt76x02_edcca_init routine signature since
it is always true
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When the hardware falls back to lower rates for a transmit attempt, only the
first status report will show the number of retries correctly. The frames
that follow will report the correct final rate, but number of retries set to 0.
This can cause the rate control module to vastly underestimate the number of
retransmissions per rate.
To fix this, we need to keep track of the initial requested tx rate per packet
and pass it to the status information.
For frames with tx status requested, this is simple: use the rate configured
in info->control.rates[0] as reference.
For no-skb tx status information, we have to encode the requested tx rate in
the packet id (and make it possible to distinguish it from real packet ids).
To do that, reduce the packet id field size by one bit, and use that bit to
indicate packet id vs rate.
This change also improves reporting by filling the status rate array with
rates from first rate to final rate, taking the same steps as the hardware
fallback table. This matters in corner cases like MCS8 on HT, where the
fallback target is MCS0, not MCS7.
Signed-off-by: Felix Fietkau <[email protected]>
Move beacon_mask in mt76_dev data structure since it is used by
all drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mac_work delayed work in mt76_dev data structure since
it is used by all drivers and it will be reused adding mac work to
mt7615
Signed-off-by: Lorenzo Bianconi <[email protected]>
