Extend mt76_connac_get_phy_mode_v2 with the per-link STA configuration.
The patch we created is a prerequisite to enable the MLO function in the
driver. It is purely a refactoring patch so the functionality should
remain unchanged.
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Extend mt76_connac_mcu_uni_add_dev with per-link BSS configuration.
The patch we created is a prerequisite to enable the MLO function in the
driver. It is purely a refactoring patch so the functionality should
remain unchanged.
We also extend link_idx field in mt76_connac_bss_basic_tlv for the firmware
to able to identify the link index in the MLO mode that is not harmful
for the current non-MLO mode.
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
This is expected by the firmware of older chipsets as well, though it may
not have been as strongly required as on mt799x
Fixes: 098428c400ff ("wifi: mt76: connac: set correct muar_idx for mt799x chipsets")
Signed-off-by: Felix Fietkau <[email protected]>
Set peer address and aid for the BMC wtbl of station interface. For some
functions such as parsing MU_EDCA parameters from beacon, firmware will
need the peer address to do correct parsing.
Without this patch, MU uplink traffic would get suffered.
Reported-by: Howard Hsu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Before sending suspend & wow command to FW, its length should be
4-bytes alignd.
Signed-off-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The wcid can be NULL. It should be checked for validity before
dereferencing it to avoid crash.
Fixes: 098428c400ff ("wifi: mt76: connac: set correct muar_idx for mt799x chipsets")
Signed-off-by: Muhammad Usama Anjum <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Because the number of channels to be configured is calculated using the %,
and it results in 0 when there's an exact division, this leads to some
channels not having their tx power configured.
Fixes: 7801da338856 ("wifi: mt76: mt7921: enable set txpower for UNII-4")
Signed-off-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The MUAR (multicast unicast address) is an address mapping table that
participates in the process of searching WTBL entries. For mt799x
chipsets, the default muar index of BMC WTBL is 0xe.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add an address of fw region for fw download.
Fixes: c948b5da6bbe ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Signed-off-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Support firmware download and enable related AFE PLL for mt7992 chipsets.
This is a preliminary patch for mt7992 chipsets support.
Co-developed-by: Benjamin Lin <[email protected]>
Signed-off-by: Benjamin Lin <[email protected]>
Co-developed-by: Shayne Chen <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: StanleyYP Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add a BSS eht_support check before returning EHT phy mode. Without this
patch, there might be an inconsistency where the softmac layer thinks
the BSS is in HE mode, while the FW thinks it is in EHT mode.
Signed-off-by: MeiChia Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt76_connac_mcu_get_nic_capability() is used by mt7921 only. It
would be better to put the code in chip folder. And we can provide
more chip capability information in mt792x_phy without making
mt76_phy much bigger.
The three functions would be moved to mt7921 folder and renamed.
mt76_connac_mcu_parse_tx_resource()
mt76_connac_mcu_parse_phy_cap()
mt76_connac_mcu_get_nic_capability()
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The variable band should be determined by the ieee80211_chanctx_conf when
the driver is a kind of chanctx one e.g mt7921 and mt7922 driver so we
added the extension to mt76_connac2_mac_tx_rate_val and
mt76_connac_get_he_phy_cap for the firmware can select the proper rate.
Fixes: 41ac53c899bd ("wifi: mt76: mt7921: introduce chanctx support")
Signed-off-by: Sean Wang <[email protected]>
Tested-by: David Ruth <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add eht field in struct mt76_power_limits for 802.11be power config.
The function stack size would be too big by eht adding in structure,
we also refactor mt76_connac_mcu_rate_txpower_band() to take dynamic
allocated memory instead.
This is a preliminary patch to support mt7925 driver.
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add eht configuration support in existing function
mt76_connac_get_phy_mode_v2() and export it for mt7925.
This is a preliminary patch to support mt7925 driver.
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt7925 rely on the similar functionalities in connac layer.
Export them for mt7925 reuse.
This is a preliminary patch to support mt7925 driver.
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce is_mt7925() helper for new chipset. mt7925 runs the same
firmware download and mmio map flow as mt7921.
This is a preliminary patch to support mt7925 driver.
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt76 scan command only support 64 channels currently. If the
channel count is larger than 64(for 2+5+6GHz), some channels will
not be scanned. Hence change the scan type to full channel scan
in case of the command cannot include proper list for chip.
Fixes: 399090ef9605 ("mt76: mt76_connac: move hw_scan and sched_scan routine in mt76_connac_mcu module")
Reported-by: Ben Greear <[email protected]>
Tested-by: Isaac Konikoff <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce p2p-go/p2p-client support to mt7921 driver
CONNECTION_P2P_GC/GO is not supported with the current firmware
so we added mt76_dev to mt76_connac_mcu_sta_basic_tlv signature to
use CONNECTION_INFRA_STA/AP instead for p2p-client and p2p-go
respectively to make it work.
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add helpers to get eht cap and phymode on different bands and vifs.
This is the preliminary patch to add EHT support for mt7996.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Due to information missing, the firmware may be fail on bandwidth
related settings in mt7921/mt7922. Add new cmd STA_REC_HE_V2 to apply
additional capabilities in 6GHz band.
Tested-by: Ben Greear <[email protected]>
Co-developed-by: Deren Wu <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce is_mt7996() helper for new chipset.
This is a preliminary patch to support mt7996 driver.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The current hw scan cannot accept multiple hw scan requests at a time, we
return the proper error code when the hw scan is still undergoing.
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add a chanctx parameter to mt76_connac_mcu_uni_add_bss signature to allow
the firmware binds the BSS into the specific channel context.
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
add mt76_connac_mcu_uni_set_chctx to set up the channel context per BSS
in the firmware
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix the regression of the firmware version report since
'b9ec27102ac0 ('mt76: connac: move mt76_connac2_load_ram in connac
module')'.
Fixes: b9ec27102ac0 ("mt76: connac: move mt76_connac2_load_ram in connac module")
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix possible unaligned pointer in mt76_connac_mcu_add_nested_tlv
routine.
Reported-by: kernel test robot <[email protected]>
Fixes: 25702d9c55dc5 ("mt76: connac: rely on le16_add_cpu in mt76_connac_mcu_add_nested_tlv")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_connac2_mcu_fill_message routine in shared module in order to
reuse it for mt7921 and mt7915e drivers. This is a preliminary patch to
add mt7990 driver support.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Due to AP stop improperly, mt7921 driver would face random command timeout
by chip fw problem. Migrate AP start/stop process to .start_ap/.stop_ap and
congiure BSS network settings in both hooks.
The new flow is shown below.
* AP start
.start_ap()
configure BSS network resource
set BSS to connected state
.bss_info_changed()
enable fw beacon offload
* AP stop
.bss_info_changed()
disable fw beacon offload (skip this command)
.stop_ap()
set BSS to disconnected state (beacon offload disabled automatically)
destroy BSS network resource
Fixes: 116c69603b01 ("mt76: mt7921: Add AP mode support")
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_connac2_load_patch utility routine in mt76_connac module since
it is shared between mt7921 and mt7915. This is a preliminary patch to
support mt7902e driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_connac2_load_ram utility routine in mt76_connac module since
it is shared between mt7921 and mt7915. This is a preliminary patch to
support mt7902e driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
use skb_put_data instead of open coding in
mt76_connac_mcu_update_arp_filter.
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Don't populate the read-only array ba_range on the stack but
instead make it static const. Also makes the object code a little
smaller.
Signed-off-by: Colin Ian King <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Since there are no HT & VHT IEs being sent in 6ghz,
some capabilities judgement and parsing for wtbl &
starec configuration should be modified to reflect such changes.
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Money Wang <[email protected]>
Signed-off-by: MeiChia Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The original single LDPC cap bit cannot be used to
differentiate LDPC cap in each PHY mode.
This modification split the single bit into 3 bits,
ht_ldpc, vht_ldpc, and he_ldpc.
Reviewed-by: Ryder Lee <[email protected]>
Suggested-by: Money Wang <[email protected]>
Signed-off-by: MeiChia Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
