This allows the core code to change the channel. Code deduplication and
preparation for adding scanning code to the core.
Signed-off-by: Felix Fietkau <[email protected]>
Extend mt76_connac_mcu_uni_add_dev with per-link BSS configuration.
The patch we created is a prerequisite to enable the MLO function in the
driver. It is purely a refactoring patch so the functionality should
remain unchanged.
We also extend link_idx field in mt76_connac_bss_basic_tlv for the firmware
to able to identify the link index in the MLO mode that is not harmful
for the current non-MLO mode.
Signed-off-by: Sean Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
The ieee80211_queue_work function queues work into the mac80211
local->workqueue, which is widely used for mac80211 internal
work processes. In the mt76 driver, both the mt76-sido-status and
mt76-sdio-net threads enqueue workers to the workqueue with this
function. However, in some cases, when two workers are enqueued
to the workqueue almost simultaneously, the second worker may not
be scheduled immediately and may get stuck for a while.
This can cause timing issues. To avoid these timing
conflicts caused by worker scheduling, replace the worker
with an independent thread.
Fixes: 48fab5bbef40 ("mt76: mt7921: introduce mt7921s support")
Signed-off-by: Wang Zhao <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mtk_wed_device pointer in mt76_queue structure in order to
configure WED chip.
Get rid of dev parameter in Q_READ and Q_WRITE macros.
Introduce wed parameter to the following routine signatures:
- mt76_init_queue
- mt76_init_tx_queue
This is a preliminary patch to introduce WED support for mt7996 since
mt7996 runs two separate WED chips.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use the correct ieee80211_conf of each band for IEEE80211_CONF_MONITOR
comparison.
Fixes: 24e69f6bc3ca ("mt76: fix monitor rx FCS error in DFS channel")
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The error handling code was added in order to allow tx enqueue to fail after
calling .tx_prepare_skb. Since this can no longer happen, the error handling
code is unused.
Signed-off-by: Felix Fietkau <[email protected]>
Rely on poll_list field in mt76_wcid structure and get rid of
private copy.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rely on sta_poll_list and sta_poll_lock fields in mt76_dev structure
and get rid of private copies.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The Group ID Management frame is an Action frame of category VHT.
It is transmitted by the AP to assign or change the user position
of a STA for one or more group IDs.
Also, sniffer can use a given group id to monitor STA that belongs
to that group.
Notify underlying driver of changes via BSS_CHANGED_MU_GROUPS.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move some mac shared definitions between mt7996, mt7921 and mt7915 in
mt76_connac2_mac.h.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
sta_ps callback is just an empty stub for most of the drivers,
so get rid of them.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Most of connac based drivers (mt7921, mt7615, mt7663) share the same
code to enable interrupts. Move it in mt76_connac module.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
irq_tasklet struct is used by most of the drivers (e.g. mt7915, mt7921,
mt7615, mt7663 and mt7996) so move it in common code.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mcu_uni_event and mcu_reg_event structs are shared between mt7921 and
mt7615 drivers, so move them in connac lib.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce p2p-go/p2p-client support to mt7921 driver
CONNECTION_P2P_GC/GO is not supported with the current firmware
so we added mt76_dev to mt76_connac_mcu_sta_basic_tlv signature to
use CONNECTION_INFRA_STA/AP instead for p2p-client and p2p-go
respectively to make it work.
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
According to the documentation, ieee80211_rx_list must not run concurrently
with ieee80211_tx_status (or its variants).
Cc: [email protected]
Fixes: 88046b2c9f6d ("mt76: add support for reporting tx status with skb")
Reported-by: Brian Coverstone <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This helps avoid cleartext leakage of already queued or powersave buffered
packets, when a reassoc triggers the key deletion.
Cc: [email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Run mt7615_mcu_restart routine directly and avoid mcu_restart function
pointer whenever it is possible.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce the capability to support per-phy led blinking. This is needed
for devices supporting dbdc.
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move leds struct in mt76_phy in order to have leds associated to phy
(e.g. in dbdc mode) instead of per device.
Tested-by: Frank Wunderlich <[email protected]>
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt7663 efuse has 0x600 bytes instead of 0x400. Increase the size in order
to fix issues with incomplete calibration data
Signed-off-by: Felix Fietkau <[email protected]>
Add a chanctx parameter to mt76_connac_mcu_uni_add_bss signature to allow
the firmware binds the BSS into the specific channel context.
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move aggregation stats array per-phy instead of share it between multiple
interfaces. This is a preliminary patch to add mt7996 driver support.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to move aggr_stats array in mt76_phy
structure.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This adds selectable RTC/CTS enablement for each interface.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Checking the relevant rxd bits for the checksum information only indicates
if the checksum verification was performed by the hardware and doesn't show
actual checksum errors. Checksum errors are indicated in the info field of
the DMA descriptor. Fix packets erroneously marked as CHECKSUM_UNNECESSARY
by checking the extra bits as well.
Those bits are only passed to the driver for MMIO devices at the moment, so
limit checksum offload to those.
Fixes: 2122dfbfd0bd ("mt76: mt7615: add rx checksum offload support")
Fixes: 94244d2ea503 ("mt76: mt7915: add rx checksum offload support")
Fixes: 0e75732764e8 ("mt76: mt7921: enable rx csum offload")
Signed-off-by: Felix Fietkau <[email protected]>
When 802.3 decap offload is enabled, the hardware indicates header translation
failure, whenever either the LLC-SNAP header was not found, or a VLAN header
with an unregcognized tag is present.
In that case, the hardware inserts a 2-byte length fields after the MAC
addresses. For VLAN packets, this tag needs to be removed. However,
for 802.3 LLC packets, the length bytes should be preserved, since there
is no separate ethertype field in the data.
This fixes an issue where the length field was omitted for LLC frames, causing
them to be malformed after hardware decap.
Fixes: 1eeff0b4c1a6 ("mt76: mt7915: fix decap offload corner case with 4-addr VLAN frames")
Reported-by: Chad Monroe <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce rx_check callback support for mt7663s driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Similar to mt7921 driver, introduce mt7615_mutex_acquire/release in
mt7615_sta_set_decap_offload in order to avoid sending mcu commands
while the device is in low-power state.
Fixes: d4b98c63d7a77 ("mt76: mt7615: add support for rx decapsulation offload")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce rx_check callback support for mt7663u and mt7921u drivers.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The code was accidentally shifting register values down by tid % 32 instead of
(tid * field_size) % 32.
Signed-off-by: Felix Fietkau <[email protected]>
Report phy_indx in tx_info->hw_queue. This is a preliminary patch to add
newer chipset support
Co-developed-by: Bo Jiao <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Introduce phy_idx to mt76_wcid structure instead of ext_phy.
This is a preliminary patch to add newer chipset support.
Co-developed-by: Bo Jiao <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Introduce phys array in mt76_dev structure to reference mt76_phy
supported by the chipset. This is a preliminary patch to introduce
newer chipset support.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Introduce phy_idx mt76_rx_status instead of ext_idx. This is a
preliminary patch to add newer chipset support
Co-developed-by: Bo Jiao <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Move mt76_connac_init_tx_queues and mt76_connac_tx_cleanup routines
in mt76_connac module. This is a preliminary patch to add mt7990
chipset support.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
