Fix the following sparse warning in mt7603_mcu_set_eeprom:
drivers/net/wireless/mediatek/mt76/mt7603/mcu.c:376:30: sparse: warning:
incorrect type in assignment (different base types)
drivers/net/wireless/mediatek/mt76/mt7603/mcu.c:376:30: sparse:
expected unsigned short [usertype] addr
drivers/net/wireless/mediatek/mt76/mt7603/mcu.c:376:30: sparse: got
restricted __le16 [usertype]
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move dfs region field in mt76_dev data structure since it is
used by all drivers. This is a preliminary patch to add DFS support to
mt7615 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Now that tx status reporting can figure out the first attempted rate, we can
make switching from lower rates to higher rates more conservative.
This reduces retries under bad link conditions and ensures that fallback
rates get more test coverage
Signed-off-by: Felix Fietkau <[email protected]>
Tx status reporting on mt7603 has a number of issues:
- the hardware can alter the first rate index, but it is not reported to
the driver
- probing is very imprecise, because it alters the per-client rate set,
but only considers info->status.rates for rate selection of a single probe
packet
- short/long GI selection has limitations, which are not accurately reported
to mac80211
- if rates are changed while packets are in flight, tx status reports for
the old rate set might be processed based on the new selection
This led to very suboptimal rate selection with minstrel_ht.
This patch completely reworks tx status reporting to get rid of these
limitations:
- Store the previous and current rate set in the driver + the TSF value
at the time of the switch.
- Use the tx status TSF value to determine which rate set needs to be used
as reference.
- Report only short or long GI rates for a single status event, not a mix.
- The hardware reports the last used rate index. Use it along with the
retry count to figure out what rate was used for the first attempt.
- Use the same retry count value for all rate slots to make this calculation
work.
- Derive the probe rate from the current rateset instead of the skb cb
- Do not wait for a status report for the probe frame before removing the
probe rate from the rate table. Do it immediately after it was referenced
in a tx status report.
- Use the first half of the first rate retry budget for the probe rate
in order to avoid using too many retries on that rate
With this patch, throughput under bad link conditions is improved
significantly, and there is a lot less rate fluctuation going on.
Signed-off-by: Felix Fietkau <[email protected]>
Fixes gcc '-Wunused-but-set-variable' warnings:
drivers/net/wireless/mediatek/mt76/mt7603/mac.c: In function mt7603_fill_txs:
drivers/net/wireless/mediatek/mt76/mt7603/mac.c:969:5: warning: variable pid set but not used [-Wunused-but-set-variable]
drivers/net/wireless/mediatek/mt76/mt7603/mac.c:961:7: warning: variable final_mpdu set but not used [-Wunused-but-set-variable]
drivers/net/wireless/mediatek/mt76/mt7615/mac.c: In function mt7615_fill_txs:
drivers/net/wireless/mediatek/mt76/mt7615/mac.c:555:5: warning: variable pid set but not used [-Wunused-but-set-variable]
drivers/net/wireless/mediatek/mt76/mt7615/mac.c:552:19: warning: variable final_mpdu set but not used [-Wunused-but-set-variable]
They are never used, so can be removed.
Signed-off-by: YueHaibing <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt7603_get_rate in mac80211.c and rename it to mt76_get_rate
since it is shared between mt7603 and mt7615 drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt7615_insert_ccmp_hdr in mac80211.c and rename it in
mt76_insert_ccmp_hdr since it is shared between mt7603 and mt7615
drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When setting chan->max_power after registering the wiphy, chan->max_reg_power
needs to be used as a limit
Signed-off-by: Felix Fietkau <[email protected]>
For the external PA (TSSI OFF) case, the target power needs to be read
from a different location in EEPROM
Signed-off-by: Felix Fietkau <[email protected]>
Introduce a knob in mt7603 debugfs in order to enable/disable
energy detection based on CCA thresholds
Signed-off-by: Lorenzo Bianconi <[email protected]>
Move netif_napi_del in mt76_dma_cleanup routine since it is done
by all drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This allows tx scheduling and tx cleanup to run concurrently
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Do not allocate mcu requests on the stack in mt7603_mcu_set_eeprom
in order to avoid the following warning:
Warning: the frame size of 1032 bytes is larger than 1024 bytes
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Disable pre_tbtt_tasklet tasklet before setting the operating channel.
Enable/disable beacon_timer in mt7603_set_channel
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move pre_tbtt_tasklet tasklet in mt76_dev data structure since
it is used by all drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move beacon_mask in mt76_dev data structure since it is used by
all drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move beacon_int in mt76_dev data structure since it is used by
all drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Print fw_ver and build_date members of struct mt7603_fw_trailer
similarly to what appears in the output of 'dmesg' when the MCU firmware
is loaded.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Run __mt76_mcu_send_msg instead of __mt7603_mcu_msg_send and remove
duplicated code.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use common function wrapper in mt7603_mcu_exit since the code is shared
with mt7615 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use __mt76_mcu_send_msg wrapper instead of mt7603_mcu_msg_send.
This is a preliminary patch for mt7615-mt7603 mcu code unification
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use mt76 common signature for mt7603_mcu_msg_send. Move skb allocation
in mt7603_mcu_msg_send and remove duplicated code. This is a preliminary
patch for mt7615-mt7603 mcu code unification
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove query parameter from mt7603_mcu_msg_send/__mt7603_mcu_msg_send
routine signature since it can be obtained from cmd value. This is a
preliminary patch for mcu code unification between mt7615 and mt7603
drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Pass skb pointer to tx_prepare_skb through mt76_tx_info data structure.
This is a preliminary patch to properly support dma error path for
new chipsets (e.g. 7615)
Signed-off-by: Lorenzo Bianconi <[email protected]>
Move mac_work delayed work in mt76_dev data structure since
it is used by all drivers and it will be reused adding mac work to
mt7615
Signed-off-by: Lorenzo Bianconi <[email protected]>
Move mt76_tx_free in mt76_free_device routine in order to
unmap all txwi descriptors at module unload
Signed-off-by: Lorenzo Bianconi <[email protected]>
- tx power is stored in the channels after ieee80211_register_hw, so
chan->orig_mpwr needs to be updated as well
- for non-TSSI devices, mt76x2e needs to use a different target power value
from the EEPROM
- fix a rounding error in a few places (need to round up, not down)
Signed-off-by: Felix Fietkau <[email protected]>
All mt76 drivers (now also USB drivers) require empty .set_tim
callback. Add it to common mt76 module and use on all drivers.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Now that the sequence number allocation is fixed, we can finally send a BAR
at powersave wakeup time to refresh the receiver side reorder window
Signed-off-by: Felix Fietkau <[email protected]>
If the MT_TXD3_SN_VALID flag is not set in the tx descriptor, the hardware
assigns the sequence number. However, the rest of the code assumes that the
sequence number specified in the 802.11 header gets transmitted.
This was causing issues with the aggregation setup, which worked for the
initial one (where the sequence numbers were still close), but not for
further teardown/re-establishing of sessions.
Additionally, the overwrite of the TID sequence number in WTBL2 was resetting
the hardware assigned sequence numbers, causing them to drift further apart.
Fix this by using the software assigned sequence numbers
Signed-off-by: Felix Fietkau <[email protected]>
Use register definitions instead of magic numbers in mt7603_reg_map
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove mt7603_mcu_init since mcu.mutex has been already initialized
in mt76_mmio_init. Run mt7603_load_firmware directly in
mt7603_init_hardware
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
As already done for mt76_dma_tx_queue_skb_raw, add static qualifier to
mt76_dma_tx_queue_skb and introduce mt76_tx_queue_skb in order to run
mt76_dma_tx_queue_skb in driver code
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add mt76_tx_info as auxiliary data structure to pass values
to tx_prepare_skb pointer. This is a preliminary patch to add
support for new chipsets (e.g. mt7615)
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt76_sw_queue data structure in order to support new
chipsets (e.g. mt7615) that have a shared hardware queue for all traffic
identifiers. mt76_sw_queue will be used to track outstanding packets
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
