Introduce mt7915 dbdc support. If dbdc is available, mt7915 primary phy
will work on 2.4GHz band, while secondary one on 5GHz band.
Co-developed-by: Shayne Chen <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mcu queue to a dedicated array q_mcu in mt76_dev structure.
This is a preliminary patch to move data queues in mt76_phy and properly
support dbdc
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to move data queues in mt76_phy and properly
support dbdc
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to move data queues in mt76_phy and properly
support dbdc
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt7915_mcu_bss_sync_tlv() is no longer used, so remove it.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Support testmode tx for MT7915A, including tx streams and HE rate
settings.
Reviewed-by: Ryder Lee <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_mcu_send_firmware routine in common code since it is actually
shared between mt7615, mt7663, mt7603 and mt7915 devices
Signed-off-by: Lorenzo Bianconi <[email protected]>
When per-packet rate reporting is enabled, the hardware can get stuck under
some conditions. It self-recovers quickly, but in practice this leads to
reduced performance.
In order to avoid running into this issue, disable per-packet rate reporting
by default and query the rx rate from firmware instead, unless monitor mode
is enabled.
Signed-off-by: Felix Fietkau <[email protected]>
The firmware/hardware supports only 16 entries. Trying to use more can lead
to timeouts on some firmware versions
Signed-off-by: Felix Fietkau <[email protected]>
When looking for a MAC address slot, start by using main BSSID slots 1-3,
afterwards use 16 repeater mode BSSID slots, then start using the slots
usually used for AP mode.
This search order should prevent unnecessary conflicts with AP mode interfaces
on the same PHY
Signed-off-by: Felix Fietkau <[email protected]>
Convert cpu_to_le16(le16_to_cpu(E1) + E2) to use le16_add_cpu().
Signed-off-by: Liu Shixin <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Release mcu message memory in case of failure in mt7915_mcu_add_beacon
routine
Fixes: e57b7901469fc ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Smatch complains that "wcidx" value comes from the network and thus
cannot be trusted. In this case, it actually seems to come from the
firmware. If your wireless firmware is malicious then probably no
amount of carefulness can protect you.
On the other hand, these days we still try to check the firmware as much
as possible. Verifying that the index is within bounds will silence a
static checker warning. And it's harmless and a good exercise in kernel
hardening. So I suggest that we do add a bounds check.
Fixes: e57b7901469f ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Signed-off-by: Dan Carpenter <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Clean up the flow of per-rate txpower limit setting to get rid of
dulplicate work since it has already been handled by firmware, and set
proper max_power based on different channels and regdomains.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is easy to add MU EDCA parameters in the future. This patch
also fixes a wrong cw_min assignment.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Enable MU-MIMO DL/UL and add relative counters in debugfs.
Currently MU modules read WTBL first to notify BA changes to
other cross modules, so adjust mt7915_mcu_sta_ba() accordingly.
Tested-by: Evelyn Tsai <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c: In function 'mt7915_mcu_sta_txbf_type':
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:1805:21: warning:
variable 'msta' set but not used [-Wunused-but-set-variable]
It is never used, so can be removed.
Reported-by: Hulk Robot <[email protected]>
Signed-off-by: YueHaibing <[email protected]>
Enable or disable OBSS PD when the bss config changes or we
assoc to an AP that broadcasts the IE.
With this patch, we can get ~20% gain in OBSS OTA environment.
Tested-by: Evelyn Tsai <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Felix Fietkau