No functional change intended.
Add SPDX identifiers to all remaining files in /mt76.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This fixes the following checkpatch warnings:
ERROR: code indent should use tabs where possible
CHECK: Alignment should match open parenthesis
CHECK: No space is necessary after a cast
CHECK: Please don't use multiple blank lines
CHECK: Avoid precedence issues in macro
WARNING: Statements should start on a tabstop
WARNING: Unnecessary space before function pointer arguments
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Reduce rx memory footprint allocating just one SG buffer since for the
moment we support just 3839B as maximal size of an A-MSDU.
Introduce different SG_MAX_SIZE definitions for TX and RX sides.
Moreover set q->buf_size to PAGE_SIZE even for SG case.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When loading EEPROM data from flash, the RF frontend settings need to be
initialized from flash data. Without this, the chip loads the wrong values
from its internal eFuse ROM.
Signed-off-by: Felix Fietkau <[email protected]>
This didn't bring the performance benefit that I had hoped for, so the mac80211
patch for this will not make it upstream
Signed-off-by: Felix Fietkau <[email protected]>
Remove enable parameter from mt76x02_edcca_init routine signature since
it is always true
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When setting chan->max_power after registering the wiphy, chan->max_reg_power
needs to be used as a limit
Signed-off-by: Felix Fietkau <[email protected]>
Move pre_tbtt_tasklet tasklet in mt76_dev data structure since
it is used by all drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mac80211 .start(), .stop() callbacks are never called concurrently with
other callbacks. The only concurencly is with mt76 works which we cancel
on stop() and schedule on start().
This fixes possible deadlock on cancel_delayed_work_sync(&dev->mac_work)
as mac_work also take mutex.
Signed-off-by: Stanislaw Gruszka <[email protected]>
On suspend mac80211 .stop callback is called before .suspend(), so
hw mac is already stopped and we do not have to do this again.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Move mac_work delayed work in mt76_dev data structure since
it is used by all drivers and it will be reused adding mac work to
mt7615
Signed-off-by: Lorenzo Bianconi <[email protected]>
Move mt76_tx_free in mt76_free_device routine in order to
unmap all txwi descriptors at module unload
Signed-off-by: Lorenzo Bianconi <[email protected]>
Since some USB device IDs are duplicated between mt76x0u, mt7601u
and mt76x2u device, check chip version on probe and return error if
not match the driver.
Don't think this is serious issue, probe most likely will fail at
some other point for wrong device, but we do not have to configure
it if we know is not our device.
Reported-by: Xose Vazquez Perez <[email protected]>
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
- tx power is stored in the channels after ieee80211_register_hw, so
chan->orig_mpwr needs to be updated as well
- for non-TSSI devices, mt76x2e needs to use a different target power value
from the EEPROM
- fix a rounding error in a few places (need to round up, not down)
Signed-off-by: Felix Fietkau <[email protected]>
Setup usb device private data. This allows to remove mt76u_buf->dev
and simplify some routines as no longer we need to get usb device
through usb interface.
Signed-off-by: Stanislaw Gruszka <[email protected]>
All mt76 drivers (now also USB drivers) require empty .set_tim
callback. Add it to common mt76 module and use on all drivers.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Create software MT_TXQ_PSD queue for USB and map it to MT_TXQ_VO
since we do not have USB endpoint for PSD. This should make
mt76_release_buffered_frames() work by sending released frames
via MT_TXQ_VO.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add sta_ps callback but dont set WCID drop sicne registers for USB
can not be accessed from tasklet context.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add implementation of beacon_ops for USB and exit function to
stop the timer if running when device is removed. Still no
actual work on pre tbtt event.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Enabling/disableing TBTT and beacon will be diffrent for USB. Introduce
beacon_ops to encapsulate that and implement it for MMIO. USB
implementation is noop for now.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move most of beaconing code into separate file and separate beacon
initialization for USB and MMIO as pre TBTT implementation for USB
will be different.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mutex->lock must not be held while cancelling workqueues, because it is held
by the workqueue items themselves
Signed-off-by: Felix Fietkau <[email protected]>
Introduce tx_aligned4_skbs in mt76_driver_ops and move
mt76_insert_hdr_pad in mt76_dma_tx_queue_skb. This is a preliminary
patch in order to unify tx dma mapping for mt76x02 and new chipsets
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
My commit 26a7b5473191 ("mt76x02: set protection according to ht
operation element") enabled by default RTS/CTS protection for OFDM
and CCK traffic, because MT_TX_RTS_CFG_THRESH is configured to non
0xffff by initvals and .set_rts_threshold callback is not called by
mac80211 on initialization, only on user request or during
ieee80211_reconfig() (suspend/resuem or restart_hw).
Enabling RTS/CTS cause some problems when sending probe request
frames by hcxdumptool penetration tool, but I expect it can cause
other issues on different scenarios.
Restore previous setting of RTS/CTS being disabled by default for
OFDM/CCK by changing MT_TX_RTS_CFG_THRESH initvals to 0xffff.
Fixes: 26a7b5473191 ("mt76x02: set protection according to ht operation element")
Signed-off-by: Stanislaw Gruszka <[email protected]>
Use usb_bulk_msg for reading MCU command responses. This simplify code
a lot.
Together with 97a3005759c ("mt76usb: allow mt76u_bulk_msg be used
for reads") it also fix possible problems with rx data buffers
not being aligned and contained within single page. After doing
page_frag_alloc(1024) consecutive page_frag_alloc(PAGE_SIZE) will
alloc PAGE_SIZE buffer at PAGE_SIZE - 1024 offset.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
ED/CCA needs to be disable before stopping the MAC to avoid hangs from tx
being blocked. It must only be enabled again after the MAC has been started
again.
In many places this wasn't done properly, so fix this by always clearing
the relevant ED/CCA bits in mt76x2_mac_stop and set it up again after
channel change or calibration is done
Signed-off-by: Felix Fietkau <[email protected]>
We need to reset MCU and do other initializations on resume otherwise
MT7610U device will fail to initialize, what cause system hung due to
USB requests timeouts.
Patch fixes 4.19 -> 4.20 regression.
Cc: [email protected] # 4.20+
Signed-off-by: Stanislaw Gruszka <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Move mt76u_check_sg routine in usb.c and introduce sg_en variable
in mt76_usb in order to check if scatter-gather is supported by
mt76u layer
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove mt76x0u_alloc_device since it just runs mt76_alloc_device.
Move mt76_alloc_device call in mt76x0u_probe and in mt76x0e_probe
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76x{0,2} alloc_device common code in mt76_alloc_device and
remove duplicated code
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove useless commented out configuration in mt76x0u_load_firmware
routine
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix rate power configuration for VHT mcs 8 and 9 in
mt76x0_get_tx_power_per_rate. Moreover use the rate power
offset used for HT/VHT mcs 6 even for HT/VHT mcs 7
Fixes: b37bbc8c8251 ("mt76x0: remove eeprom dependency from mt76x0_set_tx_power_per_rate")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
ED/CCA Tx blocking checks need to be run every 100 ms in order to avoid
triggering too late and keeping tx blocking on for too long
Signed-off-by: Felix Fietkau <[email protected]>
Add mt76x0_init_txpower in order to initialize max_power per channel
at device bootstrap. Modify mt76x0_get_tx_power_per_rate and
mt76x0_get_power_info signature in order to compute tx power for
non-operating channels
Signed-off-by: Lorenzo Bianconi <[email protected]>
Initialize target_power variable in mt76x0_phy_set_txpower in order to
report target_power in debugfs
Signed-off-by: Lorenzo Bianconi <[email protected]>
Ported from the reference driver. Should fix compliance with ETSI
regulatories on preventing transmission while energy detect values
are above the threshold.
The code has been tested using an ath9k device running tx99 as
noise generator
Signed-off-by: Lorenzo Bianconi <[email protected]>
MODULE_FIRMWARE() is used in usb_mcu.c and provided by linux/module.h,
but this header file is not directly included. This causes problems in
backports with some kernel versions.
Add the missing include.
Signed-off-by: Hauke Mehrtens <[email protected]>
We always wait for CMD_CALIBRATION_OP mcu message, but wait argument is used
for do additional MT_MCU_COM_REG0 register operations, which are needed
for mt76x2e devices and we can use appropriate check instead of wait argument.
Signed-off-by: Stanislaw Gruszka <[email protected]>
