This is a preliminary patch to properly support mt7915 dbdc
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move hw data queues in mt76_phy from mt76_dev since mt7915 supports per
phy hw queues in dbdc mode
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The newer chipsets can deal with the same STA on multiple interfaces
Preparation for supporting more station interfaces
Signed-off-by: Felix Fietkau <[email protected]>
Since the switch to using AQL by default, mtxq->retry_q is never filled anymore
Remove it to get rid of a few more unnecessary cycles in the tx path
Signed-off-by: Felix Fietkau <[email protected]>
There really is no need to make drivers call the
ieee80211_start_tx_ba_cb_irqsafe() function and then
schedule the worker if all we want is to set a bit.
Add a new return value (that was previously considered
invalid) to indicate that the driver is immediately
ready for the session, and make drivers use it. The
only drivers that remain different are the Intel ones
as they need to negotiate more with the firmware.
Link: https://lore.kernel.org/r/1570007543-I152912660131cbab2e5d80b4218238c20f8a06e5@changeid
Signed-off-by: Johannes Berg <[email protected]>
All drivers use this in pretty much the same way. Moving it to core helps with
some checks for the upcoming testmode support
Signed-off-by: Felix Fietkau <[email protected]>
All drivers before MT7915 have a limit of 128 WCID entries. Stop relying
on ARRAY_SIZE(dev->mt76.wcid), since it no longer reflects that limit.
Fixes: 49e649c3e0a6 ("mt76: adjust wcid size to support new 802.11ax generation")
Reported-by: kbuild test robot <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move WIPHY_FLAG_HAS_CHANNEL_SWITCH in mt76-core module since now all
drivers support Channel Switch Announcement
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rely on FIELD_PREP macro for led register definitions and
remove open coding
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This patch enables channel switch support on mt76 usb interfaces.
Signed-off-by: Markus Theil <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
On adding vifs the idx can become 1 + (7 & 7) = 8 for APs.
Check against that, as only AP vif idx 0-7 is possible.
Signed-off-by: Markus Theil <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix coverage_class type in mt76x02_dev data structure since
coverage_class can be negative to enable dynack (just supported by
ath9k). Set 0 as minimum value for coverage_class
Fixes: 7bc04215a66b ("mt76: add driver code for MT76x2e")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add support for an extra wiphy in mt76_set_channel and mt76_get_survey
This is preparation for supporting multiple wiphys per device to support the
concurrent dual-band feature of MT7615D
Signed-off-by: Felix Fietkau <[email protected]>
Move interface modes declaration in common code since now mt76
chipsets support all modes (NL80211_IFTYPE_STATION, NL80211_IFTYPE_AP,
NL80211_IFTYPE_MESH_POINT and NL80211_IFTYPE_ADHOC)
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move SUPPORTS_REORDERING_BUFFER hw property configuration from chip
specific code to mt76_register_device since it is supported by all mt76
drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Convert mt76_is_mmio and mt76_is_usb to rely on mt76_dev instead of
mt76x02_dev since this is a property not strictly related to hw chipset
and it will be more reusable
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
There is no need to send a BAR frame after stopping aggregation, and doing
so could lead to sending class 3 frames after deauthentication from an AP
Signed-off-by: Balakrishna Bandi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce a default implementation for mt76_sw_scan and
mt76_sw_scan_complete in mt76 module and remove duplicated code
since most of the drivers share the same implementation
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Enable multi-interface support for mt76x02u driver. For the moment
allow max two concurrent interfaces in order to preserve enough room
for ps traffic since we are using beacon slots for it.
I have successfully tested the following configuration:
- AP + STA
- AP0 + AP1
Signed-off-by: Lorenzo Bianconi <[email protected]>
Tested-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
No functional change intended.
Add SPDX identifiers to all remaining files in /mt76.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This fixes the following checkpatch warnings:
ERROR: code indent should use tabs where possible
CHECK: Alignment should match open parenthesis
CHECK: No space is necessary after a cast
CHECK: Please don't use multiple blank lines
CHECK: Avoid precedence issues in macro
WARNING: Statements should start on a tabstop
WARNING: Unnecessary space before function pointer arguments
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This didn't bring the performance benefit that I had hoped for, so the mac80211
patch for this will not make it upstream
Signed-off-by: Felix Fietkau <[email protected]>
Do not enable/disable pre_tbtt_tasklet tasklet in
mt76x02_sw_scan/mt76x02_sw_scan_complete since it is already done
setting the operating channel. Do run tbtt_tasklet while the device is
offchannel
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move pre_tbtt_tasklet tasklet in mt76_dev data structure since
it is used by all drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move beacon_int in mt76_dev data structure since it is used by
all drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mac_work delayed work in mt76_dev data structure since
it is used by all drivers and it will be reused adding mac work to
mt7615
Signed-off-by: Lorenzo Bianconi <[email protected]>
Enable AP mode. For now without multi-vif support, this will require
more testing and investigation.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is required to sent multicast/broadcast frames in USB AP
mode just after beacon.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add sta_ps callback but dont set WCID drop sicne registers for USB
can not be accessed from tasklet context.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move most of beaconing code into separate file and separate beacon
initialization for USB and MMIO as pre TBTT implementation for USB
will be different.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76x02_insert_hdr_pad in m76-core and rename it in
mt76_insert_hdr_pad in order to be used in mt76_dma_tx_queue_skb.
This is a preliminary patch in order to properly support tx dma
mapping for new chipsets (e.g. mt7615)
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt76_sw_queue data structure in order to support new
chipsets (e.g. mt7615) that have a shared hardware queue for all traffic
identifiers. mt76_sw_queue will be used to track outstanding packets
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Also update the mask first before calculating the vif index.
Fixes an issue where adding back the same interfaces in a different order
fails because of duplicate vif index use
Fixes: 06662264ce2ad ("mt76x02: use mask for vifs")
Signed-off-by: Felix Fietkau <[email protected]>
When the timer is already running, there is no need to reset the counter,
because the drift will remain the same.
Signed-off-by: Felix Fietkau <[email protected]>
