This is a preliminary patch to properly support mt7915 dbdc
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to move properly support mt7915 dbdc
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move hw data queues in mt76_phy from mt76_dev since mt7915 supports per
phy hw queues in dbdc mode
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mcu queue to a dedicated array q_mcu in mt76_dev structure.
This is a preliminary patch to move data queues in mt76_phy and properly
support dbdc
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to move data queues in mt76_phy and properly
support dbdc
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt76_init_mcu_queue utility routine in order to allocate
dedicate q_mcu pointers for mcu hw queues. This is a preliminary patch
to move data queues in mt76_phy and add dbdc support to mt7915 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rely on mt76_queue instead of qid in tx_queue_skb signature.
This is a preliminary patch to move data queues in mt76_phy and add
dbdc support to mt7915 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to move data queues in mt76_phy and properly
support dbdc
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_init_tx_queue in mac80211.c since it is shared by all
drivers.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_mcu_send_firmware routine in common code since it is actually
shared between mt7615, mt7663, mt7603 and mt7915 devices
Signed-off-by: Lorenzo Bianconi <[email protected]>
Run mt76_free_device instead of ieee80211_free_hw if device probing
fails in order to remove the already allocated mt76 workqueue
Fixes: a86f1d01f5ce5 ("mt76: move mt76 workqueue in common code")
Fixes: f1d962369d568 ("mt76: mt7915: implement HE per-rate tx power support")
Signed-off-by: Lorenzo Bianconi <[email protected]>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <[email protected]>
Signed-off-by: Allen Pais <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The newer chipsets can deal with the same STA on multiple interfaces
Preparation for supporting more station interfaces
Signed-off-by: Felix Fietkau <[email protected]>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Qinglang Miao <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Since the switch to using AQL by default, mtxq->retry_q is never filled anymore
Remove it to get rid of a few more unnecessary cycles in the tx path
Signed-off-by: Felix Fietkau <[email protected]>
Some devices using MT7628 or MT7603 have only one antenna chain connected.
Detect these using the EEPROM rx/tx path settings
Reported-by: Qin Wei <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Now that AQL works well on all mt76 drivers, completely replace the arbitrary
burst sizing and number of bursts logic for tx scheduling.
For the short period of time in which AQL does not work well yet, limit each
stations to 16 in-flight packets that have no estimated tx time.
This should avoid filling the queue if a station connects and queues up a
large number of packets before rate control information is available, especially
with hardware rate control
Signed-off-by: Felix Fietkau <[email protected]>
There really is no need to make drivers call the
ieee80211_start_tx_ba_cb_irqsafe() function and then
schedule the worker if all we want is to set a bit.
Add a new return value (that was previously considered
invalid) to indicate that the driver is immediately
ready for the session, and make drivers use it. The
only drivers that remain different are the Intel ones
as they need to negotiate more with the firmware.
Link: https://lore.kernel.org/r/1570007543-I152912660131cbab2e5d80b4218238c20f8a06e5@changeid
Signed-off-by: Johannes Berg <[email protected]>
mt7615 and newer drivers do not need this, since they use sequence number offload
Moving this code also reduces the number of callsites to make it easier to review
Signed-off-by: Felix Fietkau <[email protected]>
All drivers use this in pretty much the same way. Moving it to core helps with
some checks for the upcoming testmode support
Signed-off-by: Felix Fietkau <[email protected]>
Coverage class callback can potentially run in parallel with other
routines (e.g. mt7615_set_channel) that configures timing registers.
Run coverage class callback holding mt76 mutex
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
All drivers before MT7915 have a limit of 128 WCID entries. Stop relying
on ARRAY_SIZE(dev->mt76.wcid), since it no longer reflects that limit.
Fixes: 49e649c3e0a6 ("mt76: adjust wcid size to support new 802.11ax generation")
Reported-by: kbuild test robot <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
it will print an error message by itself when
devm_platform_ioremap_resource() goes wrong. so remove the duplicate
error message.
Signed-off-by: Dejin Zheng <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce rx-queues debugfs node in order to dump rx queues status.
This would be useful for mcu fw debugging
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
A switch from one rate index to the next only happens when tx count from
the current slot is greater than MT7615_RATE_RETRY, which is 1 has to be
subtracted from count, instead of added to it.
Signed-off-by: Felix Fietkau <[email protected]>
Sometimes mt7615_mac_set_timing gets called while the slot time is still
configured to 20. Ensure that in this case it always uses the OFDM CFend
rate.
Signed-off-by: Felix Fietkau <[email protected]>
The hardware requirements for A-MPDU density are entirely on the tx side,
not the rx side. Because of that, the IE value should stay at 0 and the
minimum value should instead be enforced in WTBL/TXWI
MT7615 has no restrictions here
Signed-off-by: Felix Fietkau <[email protected]>
The reference driver does not seem to enable it by default, only under certain
conditions, e.g. when a .bin file is loaded.
Make it opt-in via a device tree property for now, in case it is needed on some
boards.
Signed-off-by: Felix Fietkau <[email protected]>
Introduce headroom and tailroom to mt76_mcu_ops data structure in order
to unify the routine used for mcu message allocation. This is a
preliminary patch to add mt7663u support
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Always initialize to 0 mcu messages since if they are not propely
configured they could hang the firmware.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
If the minimum power is raised too much, it can make it impossible for weaker
clients to connect, and there are some scenarios where the false detects will
not go down no matter how much the sensitivity is adjusted.
Fixes connectivity issues in some rare cases
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt76_mcu data structure to contain common fields between
mt76u_mcu and mt76e_mcu.
Initialize mcu common fields in mt76_alloc_device().
Rely on mt76_mcu in mt76_mcu_rx_event and in mt76_mcu_get_response
in order to reuse them in usb code
Signed-off-by: Lorenzo Bianconi <[email protected]>
