mt7996_mmio_wed_init() set dev->mt76.hwrro_mode and rx_token_size while
building the WED configuration, before knowing whether the WED attach
can succeed. A failed attach left the enlarged rx_token_size behind and
reset hwrro_mode to MT76_HWRRO_OFF, clobbering the values that another
RX datapath owner may have configured earlier in probe: on Airoha
platforms with the wed_enable module parameter set, this broke the NPU
offload configuration set up by mt76_npu_init() (NPU offload requires
HW-RRO and a larger rx token space, and the attach always fails there
since no SoC has both an Airoha NPU and MTK WED).
Move both assignments after a successful attach, next to the existing
success-only dma_dev/irq assignments. This is safe for the regular WED
attach case: the first consumer of either field runs after probe
continues (mtk_wed_device_attach() only invokes the init_buf callback;
rx buffers are allocated via init_rx_buf from mtk_wed_start(), long
after mt7996_mmio_wed_init() has returned).
Within the WED configuration the HW-RRO checks were constant: the mode
was assigned unconditionally right before them, and the hif2 path is
only reachable after a successful main attach has set it. Resolve them
to their constant values and drop the dead branches.
Fixes: 377aa17d2aed ("wifi: mt76: mt7996: Add NPU offload support to MT7996 driver")
Signed-off-by: Felix Fietkau <[email protected]>
If the WED attach for the primary PCIe function fails, the probe path
still attached wed_hif2 for the secondary function, leaving the device
in an inconsistent half-WED configuration that crashes later. The hif2
call also re-enabled hwrro_mode, which the failed primary attach had
just turned off.
Skip the hif2 WED setup when the primary WED device is not active.
Fixes: 83eafc9251d6 ("wifi: mt76: mt7996: add wed tx support")
Signed-off-by: Felix Fietkau <[email protected]>
The MIB_TSCR0-7 counters read by mt7996_mac_update_stats() are
hardcoded at the mt7996/mt7992 offsets 0x6b0-0x6d0, but mt7990 moved
them to 0x750-0x770, so TX AMPDU statistics were read from unrelated
registers on that chip. Move the offsets into the per-chip register
tables.
Fixes: f6c87411d15f ("wifi: mt76: mt7996: rework register mapping for mt7990")
Signed-off-by: Felix Fietkau <[email protected]>
When addr is less than the hardcoded threshold in __mt7996_reg_addr,
it indicates that remapping is unnecessary.
Currently, the flow remaps address 0x0 to MT_HIF_REMAP_BASE_L2,
which is incorrect.
To address this, modify __mt7996_reg_addr to return INVALID_REG_ADDR
if the address is not below the hardcoded value or is not present in
the mt7996_reg_map array.
Additionally, update the remap condition to check if addr is equal to
INVALID_REG_ADDR.
Fixes: 3687854d3e7e ("wifi: mt76: mt7996: add locking for accessing mapped registers")
Signed-off-by: StanleyYP Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Enable MT_DRV_HW_PS_BUFFERING and handle MCU_UNI_EVENT_PS_SYNC with
all three TLV formats (single client, multi-client packed entries,
and bitmap).
Signed-off-by: Felix Fietkau <[email protected]>
Introduce Airoha NPU support to MT7996 driver. NPU is used to enable
traffic forward offloading between the MT76 NIC and the Airoha ethernet one
available on the Airoha EN7581 SoC using Netfilter Flowtable APIs.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
MediaTek has asked to switch from the ISC license to BSD-3-Clause-Clear,
in order to improve clarity and the legal integrity of the code.
The BSD-3-Clause license includes the "no endorsement" clause, which is
important for protecting the reputation of the original authors and
contributors by preventing unauthorized use of their names for endorsement
purposes.
This clause is absent in the BSD-2-Clause license, which is more permissive
but lacks this specific protection.
This change also cleans up the license of some Kconfig/Makefile files,
which were accidentally marked as GPL.
The GPL 2.0 remains in use on mt76x0, as well as two source files in mt7615
for which the license situation still needs to be clarified.
Signed-off-by: Felix Fietkau <[email protected]>
Introduce rx_rro_ind_process and rx_rro_add_msdu_page callbacks and the
related logic in the MT7996 driver. This is a preliminary patch to
decouple RRO logic from WED support and reuse RRO when WED module is not
available.
Signed-off-by: Rex Lu <[email protected]>
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Introduce the second WDMA RX ring in WED driver for MT7988 SoC since the
Mediatek MT7992 WiFi chipset supports two separated WDMA rings.
Add missing MT7988 configurations to properly support WED for MT7992 in
MT76 driver.
Co-developed-by: Rex Lu <[email protected]>
Signed-off-by: Rex Lu <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
devm_ioremap() returns NULL on error. Currently, mt7996_mmio_wed_init()
does not check for this case, which results in a NULL pointer
dereference.
Prevent null pointer dereference in mt7996_mmio_wed_init()
Fixes: 83eafc9251d6 ("wifi: mt76: mt7996: add wed tx support")
Signed-off-by: Henry Martin <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
The chipset name (i.e., brand name) used by the driver may cause confusion
with the PCI device ID when adding support for new chipsets.
| Chipset name | PCI device id |
|--------------|----------------|
| 7996 | 0x7990, 0x7991 |
| 7992 | 0x7992, 0x799a |
| 7990 | 0x7993, 0x799b |
To prevent confusion, replace the code that directly uses the device ID
with macros. This is a preliminary patch to support mt7990 chipset.
Co-developed-by: Peter Chiu <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7996_sta_state routine in order to initialize wcid structure
in mt7996 codebase. This is a preliminary patch to enable MLO support in
MT7996 driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
The firmware needs a specific trigger when WED is being reset due to an
ethernet reset condition. This helps prevent further L1 SER failure.
Signed-off-by: Rex Lu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use generic mt76 chanctx functions and look up phy from vif link.
The driver now uses only a single phy to handle multiple interfaces on
different channels. This is preparation for full MLO support.
Signed-off-by: Felix Fietkau <[email protected]>
This allows the core code to change the channel. Code deduplication and
preparation for adding scanning code to the core.
Signed-off-by: Felix Fietkau <[email protected]>
Set intr1 to 0 in mt7996_irq_tasklet() in order to avoid possible
uninitialized variable usage if wed is not active for hif2.
Fixes: 83eafc9251d6 ("wifi: mt76: mt7996: add wed tx support")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce wed.c in order to collect mt76 wed common codebase used by
mt7915 and mt7996 drivers.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
A race condition was observed when accessing mapped registers, so add
locking to protect against concurrent access.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add mt7992_offs to differentiate registers that share the same
definitions with mt7996 chipsets but have differnet offsets.
This is a preliminary patch for mt7992 chipsets support.
Signed-off-by: StanleyYP Wang <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce the capability to reset mt7996 chipset if requested by wed
driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Similar to MT7915, enable Wireless Ethernet Ditpatcher for MT7996
to offload traffic received from the WLAN nic and transmitted on the
LAN one
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Co-developed-by: Sujuan Chen <[email protected]>
Signed-off-by: Sujuan Chen <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Similar to MT7915, enable Wireless Ethernet Ditpatcher for MT7996
to offload traffic received from the LAN nic and transmitted on the
WLAN one
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sujuan Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
sta_ps callback is just an empty stub for most of the drivers,
so get rid of them.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
irq_tasklet struct is used by most of the drivers (e.g. mt7915, mt7921,
mt7615, mt7663 and mt7996) so move it in common code.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Host triggered and catastrophic event triggered firmware core dumping
for basic firmware issues triage, including state reporting, function
calltrace and MCU memory dump.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add mt7996_reset() and refactor mt7996_mac_reset_work() to support
full system recovery.
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Drop mt7996_tx_complete_skb routine since it is equivalent to
mt76_connac_tx_complete_skb().
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt7996_txp structure is equal to mt76_connac_fw_txp one. Drop mt7996_txp
and rely on mt76_connac_txp_common.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In newer chipsets, CFEND_RATE setting has been moved to different hw
module.
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
addr <= MT_CBTOP2_PHY_END(0xffffffff) is always true (<= u32max),
so drop it.
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This reports signal strength of ACK packets from the peer as measured
at each interface.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
