The firmware wants active links removed from the BSSINFO table as the interface
is destroyed, so a link stays registered from its first chanctx assignment until
the interface goes away, and adding one the driver already holds does nothing.
mac80211 hands a non-AP MLD a fresh address whenever it sets a link up, though,
so a link coming back after a failed attempt carries an address the hardware was
never told about, on a BSS that was never revisited: it authenticates from an
address nothing answers, every time, until the interface is torn down for good.
Program the address and the BSS again, the pair the initial add sets up, which
is for a station what mt7996_mcu_mld_link_oper() does for an AP.
Signed-off-by: Felix Fietkau <[email protected]>
When mac80211 leaves the link unspecified, mt7996_tx() substitutes the
primary link id of the station or vif. That value is
IEEE80211_LINK_UNSPECIFIED (0xf) until the first link has been added,
and it is then used unchecked to index vif->link_conf[],
mvif->mt76.link[] and sta->link[], all of which hold
IEEE80211_MLD_MAX_NUM_LINKS (15) entries.
Clamp the primary link id to the default link before using it, and use
the clamped value for the link_sta fallback as well.
Fixes: 1609b014aa29 ("wifi: mt76: mt7996: Overwrite unspecified link_id in mt7996_tx()")
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
mt7996_remove_interface() destroys the remaining vif links, clearing
omac_mask, vif_mask and mld_idx_mask, with only the wiphy mutex held.
Those masks are modified under dev->mutex everywhere else, so the
unlocked clears can race the scan-link teardown and the reset work
and lose updates.
Take dev->mutex around the link destroy loop, matching
mt7996_add_interface() and mt7915_remove_interface(). The mutex is
released before mt76_vif_cleanup(), which aborts a pending scan and
takes the mutex itself.
Signed-off-by: Chad Monroe <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The net_setup_tc callback is chosen at compile time and the WED
handler shadows the NPU one when CONFIG_NET_MEDIATEK_SOC_WED is
enabled. mt76_wed_net_setup_tc() returns -EOPNOTSUPP without an
active WED device, so on boards using the Airoha NPU with a WED
enabled kernel the tc offload block is never bound and PPE flow
offload for wireless traffic is silently disabled.
Dispatch on the active offload backend instead: use the WED handler
when a WED device is attached and fall back to the NPU handler
otherwise. Builds without MT76_NPU keep the old behavior through the
mt76_npu_net_setup_tc() stub.
Signed-off-by: Chad Monroe <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
No hw keys are ever uploaded for scanning/roc links and the link remove
path already skips the key iteration for them. The add path still runs
it, and since mt7996_set_hw_key() resolves the target through
mvif->link[link_id] rather than the offchannel link, starting a scan on
another band re-uploads the group keys of the link sharing the same
link_id, re-sending its BSS cipher info and, for BIGTK with beacon
protection on an AP link, toggling its beacons off and on.
Skip the key iteration for offchannel links, mirroring the remove path.
Fixes: 69d54ce7491d ("wifi: mt76: mt7996: switch to single multi-radio wiphy")
Signed-off-by: Felix Fietkau <[email protected]>
Because 4 address non-AMSDU packets do not have a bssid field, the
hardware cannot get the bssid. Without the bssid, stations are not
able to leave PS mode due to HW design. Wake up non-setup links when
4-address mode is established to prevent this issue.
mt7992 and mt7990 handle this via the BSSID mapping band config
instead, so restrict the command to mt7996.
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt7996_change_vif_links() sets the mld_idx_mask group bit before
allocating the remap index. If the remap allocation fails it jumped to
the exit without clearing that bit, permanently consuming one of the 16
MLD group slots. Release the group bit on the error path.
Fixes: 4fb3b4e7d1ca ("wifi: mt76: mt7996: fix MLD group index assignment")
Signed-off-by: Felix Fietkau <[email protected]>
mt7996_sta_statistics() set NL80211_STA_INFO_TX_BITRATE unconditionally
after the block that already sets it, so a station with no rate info yet
was reported to userspace with a valid-but-zero TX rate. Drop the
redundant unconditional assignments; the in-block ones are sufficient.
Fixes: b34f346b917e ("wifi: mt76: mt7996: drop return in mt7996_sta_statistics")
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Problem:
MCU command timeout while the firmware state is normal, and the
firmware keeps showing the error log "ERROR!! NO PAUSE...".
Root cause:
If the MLD_ID field in the TXD is neither the primary link id nor the
secondary link id, it may lead to a firmware busy loop when the third
link is in power saving mode.
Remap frames directed to a third link to the primary link wcid. Since
TX status events and txfree completions carry the wcid the firmware
saw, use the remapped wcid for packet id tracking and non-AQL packet
accounting as well, while the frame keeps its original link context
for addressing, band and OMAC selection.
Fixes: 85cd5534a3f2 ("wifi: mt76: mt7996: use correct link_id when filling TXD and TXP")
Signed-off-by: Peter Chiu <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
The MLO link-reconfiguration rework moved the per-phy num_sta
decrement inside a link_valid guard. link_valid is only set for
MLO links, but num_sta is incremented for every station link,
including the non-MLO deflink. Non-MLO stations bump num_sta
on association and never drop it on removal.
A non-zero num_sta forces connected-mode off-channel scanning which
prevents the directed probe exchange needed to find hidden APs.
Decrement phy->num_sta on the actual link teardown, pairing it with
the unconditional increment on link creation.
Fixes: 018f60316d ("wifi: mt76: mt7996: Destroy active sta links in mt7996_mac_sta_remove()")
Signed-off-by: Chad Monroe <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add hardware airtime fairness (ATF) support for mt7996, using the MAC's
weighted DWRR scheduler (VoW) to balance TX airtime between stations, in
the same way as the mt7915 implementation.
This supplements mac80211's software airtime fairness rather than
replacing it: software ATF keeps scheduling the host TX queues, while the
hardware scheduler enforces fairness on the offloaded path where the host
has no airtime accounting, such as when WED is active.
A station's TX airtime weight is taken from mac80211 through the
sta_set_airtime_weight op and applied to the hardware scheduler directly;
the per-AC DWRR quantum levels and the station's BSS group index are
derived on the fly, mapping the weight logarithmically onto the global
hardware quantum table. ATF and WATF are enabled by default and can be
toggled together at runtime through the "vow_atf" debugfs file.
Signed-off-by: Benjamin Lin <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Calls to mt7996_set_bitrate_mask() would propagate work for all stations
on the ieee80211_hw regardless of the vif specified in the call. To
prevent unnecessary work in FW, limit setting the sta_rate to only the
specified vif in mt7996_sta_rate_ctrl_update().
Fixes: afff4325548f0 ("wifi: mt76: mt7996: Use proper link_id in link_sta_rc_update callback")
Signed-off-by: Dylan Eskew <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
With HW TX encap offload enabled, the mt76 firmware builds the 802.11
header for the 802.3 frame using the per-WCID context. For a STATION
vif the HDR_TRANS TLV currently sets ToDS=1, which makes the firmware
default to the BSSID as A1 and emit STA->AP-formatted frames
regardless of which peer the WCID points to.
For TDLS-paired peers this is wrong. Data frames go on air addressed
to the AP, the AP MAC-ACKs and silently drops them per IEEE 802.11z
(an AP must not forward to a TDLS-paired peer). Management and
control frames bypass the HW encap path and still reach the peer;
only user data fails.
Add MT_WCID_FLAG_TDLS_PEER, set it in mt7915, mt7921, mt7925 and
mt7996 sta-add paths when sta->tdls is true, and override the
HDR_TRANS TLV in mt76_connac_mcu_wtbl_hdr_trans_tlv() (Connac2 -
mt7915 / mt7921 / mt7922), mt7925_mcu_sta_hdr_trans_tlv() (mt7925)
and mt7996_mcu_sta_hdr_trans_tlv() (mt7996) to set ToDS=0, FromDS=0
when the flag is set. The 3-addr non-DS form matches what 802.11z
uses for direct links; the firmware then constructs the frame with
A1=peer rather than A1=BSSID. HW encap offload remains enabled for
AP and any non-TDLS traffic.
Verified on mt7925e + Samsung S938B over a 5 GHz HE 80 MHz channel
with iperf3 -t 30 to the TDLS peer:
before fix: over the TDLS direct link, 7 TDLS Setup action
frames and 3 RTS frames reach the peer; 0 QoS
Data frames make it through (mgmt/control paths
bypass HW encap, the data path does not). iperf3
stalls.
after fix: 2.90 GBytes transferred at 830 Mbit/s sustained,
0 TCP retransmits.
mt7915, mt7921, mt7922 and mt7996 are not regression-tested in this
change for lack of hardware. Their HDR_TRANS handling mirrors the
verified mt7925 change; the firmware behavior is shared across these
chips.
Signed-off-by: ElXreno <[email protected]>
Assisted-by: Claude:claude-opus-4-7 bpftrace tcpdump
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Similar to vif link management, postpone sta link destuction in
mt7996_mac_sta_remove() introducing mt7996_mac_sta_remove_link utility
routine and just disable sta link running mt7996_mac_sta_remove_links
routine.
This is a preliminary patch in order to support MLO link reconfiguration
in MT7996 driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7996_mcu_mld_reconf_stop_link and mt7996_mcu_mld_link_oper
utility routines in order to communicate to the mcu fw to disable/enable
a specific vif link. Please note these APIs are currently supported by
the MT7996 firmware only in AP mode.
Signed-off-by: Shayne Chen <[email protected]>
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
MT7996 hw requires to remove active links from the mcu BSSINFO table
destroying the interface. For this reason introduce mt7996_vif_link_destroy
routine and remove active (non-offchannel) vif links running
mt7996_remove_interface routine.
This is a preliminary patch in order to support MLO link reconfiguration
in MT7996 driver.
Co-developed-by: Shayne Chen <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Destroy mt76_vif_link struct in mt7996_vif_link_remove routine and not
in mt76_unassign_vif_chanctx(). This is necessary since, in order to
properly support MLO link reconfiguration, we will destroy mt76_vif_link
struct during AP tear-down process and not running unassign_vif_chanctx
mac80211 callback.
This patch does not introduce any regression since
mt76_assign_vif_chanctx/mt76_unassign_vif_chanctx APIs are currently
used just by MT7996 driver.
Signed-off-by: Shayne Chen <[email protected]>
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Track active vif links in mt7996_vif_link_add and mt7996_vif_link_remove
routines.
This is a preliminary patch in order to remove AP MLD links from MCU
configuration during AP tear-down process and to support MLO link
reconfiguration in MT7996 driver.
Signed-off-by: Shayne Chen <[email protected]>
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Rely on msta_link link_id value in mt7996_vif_link_remove routine
instead of using link_conf pointer. This assumption is correct since
msta_link link_id is set to link_conf link_id value in mt7996_vif_link_add
routine.
Moreover, fallback to default ieee80211_bss_conf struct if the link_conf
pointer in mt7996_vif_link_remove() is NULL.
MT7996 hw requires to remove AP MLD links from MCU configuration during
AP tear-down process (e.g. running mt7996_remove_interface()). Doing so,
we can't assume link_conf pointer is always non-NULL running
mt7996_vif_link_remove routine.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Do not switch default link to the secondary link in
mt7996_mac_sta_remove_links routine if the lookup for the secondary
msta_link fails.
Fixes: d7e5444f9eb02 ("wifi: mt76: mt7996: Switch to the secondary link if the default one is removed")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Remove link pointer dependency in mt7996_mac_sta_remove_links routine to
get the mt7996_phy pointer since the link can be already offchannel
running mt7996_mac_sta_remove_links(). Rely on __mt7996_phy routine
instead.
Fixes: 344dd6a4c919 ("wifi: mt76: mt7996: Move num_sta accounting in mt7996_mac_sta_{add,remove}_links")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Link: https://patch.msgid.link/20260306-mt7996-deflink-lookup-link-remove-v1-1-7162b332873c@kernel.org
Signed-off-by: Felix Fietkau <[email protected]>
With chanctx drivers using hardware scan or remain-on-channel,
mac80211 does not know when the radio goes off-channel, which breaks
its software beacon loss detection.
Implement per-link beacon monitoring in the driver. Track the last
beacon timestamp per link and check for beacon loss periodically from
the mac_work handler.
Beacon monitoring is initialized on association and on late link
activation, and cleared on disassociation. The beacon_mon_last
timestamp is reset when returning from offchannel and after channel
switches to prevent false beacon loss detection.
Signed-off-by: Felix Fietkau <[email protected]>
During hardware restart, link_id can be IEEE80211_LINK_UNSPECIFIED,
causing an out-of-bounds array access on msta->link[].
Add mt7996_sta_link() and mt7996_sta_link_protected() helper functions
for accessing sta links with proper RCU handling and bounds checking.
Use them for any sta link RCU access.
Reported-by: Chad Monroe <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This patch adds support for handling BSS_CHANGED_ERP_CTS_PROT and
BSS_CHANGED_HT.
With this change, when the Wi-Fi driver needs to adjust its behavior for
compatibility or performance, especially concerning older 11g/n devices,
by enabling or disabling CTS protection frames, often for hidden SSIDs or
to manage legacy clients.
It also introduces debugfs options to manually control protection mode,
allowing users to select betweenno protection, RTS/CTS, and CTS-to-self.
Reviewed-by: Money Wang <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Link: https://patch.msgid.link/942ddb5777d5c201930d6609e9ba877a6ba6714a.1768879119.git.ryder.lee@mediatek.com
Signed-off-by: Felix Fietkau <[email protected]>
Clear WCID pointer removing the sta link in mt7996_mac_sta_deinit_link
routine.
Fixes: dd82a9e02c054 ("wifi: mt76: mt7996: Rely on mt7996_sta_link in sta_add/sta_remove callbacks")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Switch to the secondary link if available in mt7996_mac_sta_remove_links
routine if the primary one is removed.
Moreover reset secondary link index for single link scenario.
Fixes: 85cd5534a3f2e ("wifi: mt76: mt7996: use correct link_id when filling TXD and TXP")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Reset WCID index in mt76_txq struct if primary link is removed in
mt7996_vif_link_remove routine.
Fixes: a3316d2fc669f ("wifi: mt76: mt7996: set vif default link_id adding/removing vif links")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Set WCID index in mt76_txq struct just for the primary link in
mt7996_vif_link_add routine.
Fixes: 69d54ce7491d0 ("wifi: mt76: mt7996: switch to single multi-radio wiphy")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
After channel switch, some tags of BSSINFO (rfch) and STAREC (bfer,
rate_ctrl) commands should also be updated. Otherwise, a BSS might not be
able to transmit with its peer using correct bandwidth.
Co-developed-by: Shayne Chen <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: StanleyYP Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
RDD_DET_MODE is a firmware command intended for testing and does not
pause TX after radar detection, so remove it from the normal flow;
instead, use the MAC_ENABLE_CTRL firmware command to resume TX after
the radar-triggered channel switch completes.
Fixes: 1529e335f93d ("wifi: mt76: mt7996: rework radar HWRDD idx")
Co-developed-by: Shayne Chen <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: StanleyYP Wang <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Currently, per-radio attributes are set on per-phy basis, i.e., all the
radios present in a wiphy will take attributes values sent from user. But
each radio in a wiphy can get different values from userspace based on
its requirement.
To extend support to set per-radio attributes, add support to get radio
index from userspace. Add an NL attribute - NL80211_ATTR_WIPHY_RADIO_INDEX,
to get user specified radio index for which attributes should be changed.
Pass this to individual drivers, so that the drivers can use this radio
index to change per-radio attributes when necessary. Currently, per-radio
attributes identified are:
NL80211_ATTR_WIPHY_TX_POWER_LEVEL
NL80211_ATTR_WIPHY_ANTENNA_TX
NL80211_ATTR_WIPHY_ANTENNA_RX
NL80211_ATTR_WIPHY_RETRY_SHORT
NL80211_ATTR_WIPHY_RETRY_LONG
NL80211_ATTR_WIPHY_FRAG_THRESHOLD
NL80211_ATTR_WIPHY_RTS_THRESHOLD
NL80211_ATTR_WIPHY_COVERAGE_CLASS
NL80211_ATTR_TXQ_LIMIT
NL80211_ATTR_TXQ_MEMORY_LIMIT
NL80211_ATTR_TXQ_QUANTUM
By default, the radio index is set to -1. This means the attribute should
be treated as a global configuration. If the user has not specified any
index, then the radio index passed to individual drivers would be -1. This
would indicate that the attribute applies to all radios in that wiphy.
Signed-off-by: Roopni Devanathan <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Johannes Berg <[email protected]>
Grab mt76 mutex in mt7996_mac_sta_event routine in order to rely on
mt76_dereference() utility macro.
Fixes: ecd72f9695e7e ("wifi: mt76: mt7996: Support MLO in mt7996_mac_sta_event()")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Tested-by: Ben Greear <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
This patch fixes the following key issues:
- Pass correct link BSS to mt7996_mcu_add_key(), and use HW beacon
protection mode for mt7990 chipset
- Do not do group key deletion for GTK and IGTK due to FW design, the
delete key command will delete all group keys of a link BSS
- For deleting BIGTK, FW adds a new flow, but the "sec->add" field
should be filled with "SET_KEY". Note that if BIGTK is not deleted, it
will cause beacon decryption issue when switching from an AP interface
to a station interface
Fixes: 0c45d52276fd ("wifi: mt76: mt7996: fix setting beacon protection keys")
Co-developed-by: Allen Ye <[email protected]>
Signed-off-by: Allen Ye <[email protected]>
Co-developed-by: Peter Chiu <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Obtain the correct link ID and, if needed, switch to the corresponding
wcid before populating the TX descriptor and TX payload.
Rules for link id:
- For QoS data of MLD peers (excluding EAPOL), select the primary or
secondary wcid based on whether the TID is odd or even to meet FW/HW
requirements
- For other packets, use IEEE80211_TX_CTRL_MLO_LINK if specified
(such as multicast and broadcast packets)
Signed-off-by: Shayne Chen <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
For an MLD peer, we only need to call the teardown command when removing
the last link, and there's no need to call mt7996_mcu_add_sta() for the
earlier links.
Fixes: c1d6dd5d03eb ("wifi: mt76: mt7996: Add mt7996_mcu_teardown_mld_sta rouine")
Signed-off-by: Shayne Chen <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Introduce Airoha NPU support to MT7996 driver. NPU is used to enable
traffic forward offloading between the MT76 NIC and the Airoha ethernet one
available on the Airoha EN7581 SoC using Netfilter Flowtable APIs.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
Remove unnecessary link_id checks in mt7996_tx routine since if the link
identifier provided by mac80211 is unspecified the value will be
overwritten at the beginning on the function.
Fixes: f940c9b7aef6 ("wifi: mt76: mt7996: Set proper link destination address in mt7996_tx()")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
