This is primarily for testing and can be used in combination with monitor
mode to make the card respond to packets sent to a specific MAC address.
For now this is only exposed as a debug/testing feature, later on the
approach might be used to support more concurrent station interfaces
Signed-off-by: Felix Fietkau <[email protected]>
Introduce support for mt7663s 802.11ac 2x2:2 chipset to mt7615 driver.
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Supports sending a configurable number of packets with a specific rate
and configurable tx power levels / antenna settings, as well as displaying
rx statistics.
Signed-off-by: Felix Fietkau <[email protected]>
Now that the bus access functions can use mapping for accessing full
register addresses, use it for WF_PHY registers to keep them constant.
Needed for follow-up work on testmode support
Signed-off-by: Felix Fietkau <[email protected]>
Enable mac80211 TDLS support by default. Disable TDLS hw filtering for
mt7615 devices
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add missing register definitions in order to enable sensitivity tuning
for mt7663 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce support for mt7663u 802.11ac 2x2:2 chipset to mt7615 driver.
Main difference respect to pcie code base is the usb code needs to
configure wtbl from non-atomic context
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Simplify mib macros and use proper type for related counters.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In order to reuse mt7615 code adding support for mt7663e driver,
introduce mt7615e_reg_map since mt7663e and mt7615 rely on a
different base registers definitions.
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Co-developed-by: Ryder Lee <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When the firmware detects a problem, it needs the host to stop/reset DMA and
resume it again when the hardware state has been reset.
Signed-off-by: Felix Fietkau <[email protected]>
MT7622 does not have a CR4 microcontroller, so it only uses its own N9
firmware.
Co-developed-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
MT7622 queue mapping is different from MT7615 and requires an extra dma
scheduler init and a few register tweaks
Co-developed-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
MT7622 uses more interrupt bits for queue tx completion events.
Enabling those extra bits is harmless on MT7615
Co-developed-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
MT7615 supports dual-wiphy which means that it can run on 2.4G and 5GHz
channels simultaneously, and driver should configure each band.
Add missing register settings, and refine band related definitions to
avoid duplicate codes.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Initialize brightness_set and blink_set callbacks to
mt7615_led_set_brightness and mt7615_led_set_blink in order to enable
LED support in mt7615 driver
Tested-by: Deng Qingfang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add the capability to configure acktimeout for mt7615 driver. Moreover
configure slottime according to the value provided by mac80211
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Program the RMAC CHFREQ registers to properly indicate the band that the
frames are received on.
Add some sanity checks to the programmed values, because the firmware
programs these registers differently
Signed-off-by: Felix Fietkau <[email protected]>
Parse configured {tx,rx} mask from eeprom data instead of just setting it
to four tx-rx streams
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Poll per-station hardware counters available in WTBL after tx/rx
status events in order to report tx/rx airtime to mac80211 layer
Co-developed-by: Felix Fietkau <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Like on mt7603, MIB status register 16 tracks CCA time, but does not
include tx time. Switch to status register 9 to includ NAV and tx
time as well.
Signed-off-by: Felix Fietkau <[email protected]>
Report tx time/rx time and obss time from hw mib counters to fill survey
info requested by mac80211
Co-developed-by: Felix Fietkau <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce ampdu_stat entry in mt7615 debugfs in order to dump 802.11
aggr cumulative statistics
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7615_queues_read routine to dump hw queue related info.
Add hw ac queues statistics in mt7615 debugfs
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce channel survey support for mt7615 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce Smart Carrier Sense support in order to tune device
sensitivity according to RTS error rate and False CCA reported by the
radio
Tested-by: Ryder Lee <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add mt7615_mac_wtbl_set_key routine to configure wtbl key parameter
directly from host cpu. This is a preliminary patch to add BIP_CMAC_128
hw support. Moreover add static qualifier to mt7615_mac_get_key_info
routine
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
- Store the previous and current rate set in the driver + the TSF value
at the time of the switch.
- Use the tx status TSF value to determine which rate set needs to be used
as reference.
- Report only short or long GI rates for a single status event, not a mix.
- The hardware reports the last used rate index. Use it along with the
retry count to figure out what rate was used for the first attempt.
- Use the same retry count value for all rate slots to make this calculation
work.
- Derive the probe rate from the current rateset instead of the skb cb
- Do not wait for a status report for the probe frame before removing the
probe rate from the rate table. Do it immediately after it was referenced
in a tx status report.
- Use the first half of the first rate retry budget for the probe rate
in order to avoid using too many retries on that rate
- Switch from lower rates to higher rates more conservatively
- enable hardware rate up/down selection
Signed-off-by: Felix Fietkau <[email protected]>
These values must be initialized to zero, otherwise the hardware could
reuse previous values, especially the rate index
Signed-off-by: Felix Fietkau <[email protected]>
This driver is for a newer generation of MediaTek MT7615 4x4 802.11ac
PCIe-based chipsets, which support wave2 MU-MIMO up to 4 users/group
and also support up to 160MHz bandwidth.
The driver fully supports AP, station and monitor mode.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Roy Luo <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
