Now that AQL works well on all mt76 drivers, completely replace the arbitrary
burst sizing and number of bursts logic for tx scheduling.
For the short period of time in which AQL does not work well yet, limit each
stations to 16 in-flight packets that have no estimated tx time.
This should avoid filling the queue if a station connects and queues up a
large number of packets before rate control information is available, especially
with hardware rate control
Signed-off-by: Felix Fietkau <[email protected]>
mt7615 and newer drivers do not need this, since they use sequence number offload
Moving this code also reduces the number of callsites to make it easier to review
Signed-off-by: Felix Fietkau <[email protected]>
Remove unused state variable in mt76_sdio structure
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In order to maximize parallelism, split status work in tx status work
and rx net work
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
As it has been done for tx and rx processing, move tx/rx status
processing into mt76s_txrx_wq workqueue
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move rx processing to mt76s_txrx_wq in order to minimize the interval when
the sdio bus is locked during rx
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt76s_txrx_wq workqueue and move tx processing from kthread to
a dedicated work. This is preliminary patch to improve mt7663s throughput
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
A small part of the first skb buffer is passed to the firmware for parsing
via DMA, while the full buffer is passed as part of the TXP.
Avoid calling DMA unmap on the first part (with a different length than map)
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt76_sdio module as common layer to add mt7663s support
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Introduce mt76_skb_adjust_pad to reuse the code adding sdio support to
mt7615 driver and remove code duplication. Move 4B header configuration
for usb devices out of mt76_skb_adjust_pad
Signed-off-by: Lorenzo Bianconi <[email protected]>
Introduce mt7615_update_survey utility routine in order to compute
survey stats without waking up the device since it runs holding mt76 lock.
Run mt7615_pm_wake directly in mt7615_update_channel since it can run
with mt76.mutex held if called by mac80211
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7615_pm_wake utility routine to wake the device from
runtime low-power state (lower-power state is currently supported by
offload firmware for pcie devices).
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76 workqueue from usb to common code in order to be reused adding
low-power support for mt7663 chipset
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This can be used for calibration in the manufacturing process.
It supports sending a configurable number of packets with a specific rate
and configurable tx power levels / antenna settings.
It also supports receiving packets and showing some statistics, including
packet counters and detailed RSSI information.
It will only be compiled in if CONFIG_NL80211_TESTMODE is enabled
Signed-off-by: Felix Fietkau <[email protected]>
All drivers use this in pretty much the same way. Moving it to core helps with
some checks for the upcoming testmode support
Signed-off-by: Felix Fietkau <[email protected]>
This subnode can be used to set per-rate tx power limits either per
country code / regdomain or globally.
These limits are typically provided by the device manufacturers and are
used to limit sideband emissions and stay within regulatory limits
Signed-off-by: Felix Fietkau <[email protected]>
Overwrite hw queue id for non-bufferable management frames if the hw
support always txq (altxq) in order to be in sync with mac txwi code
Fixes: cdad4874057d ("mt76: mt7615: add dma and tx queue initialization for MT7622")
Fixes: f40ac0f3d3c0 ("mt76: mt7615: introduce mt7663e support")
Suggested-by: Felix Fietkau <[email protected]>
Tested-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt76 core uses ffs() to find the next free bit. This works well for 32 bit
architectures where BITS_PER_LONG is 32. ffs only checks 32 bit values, so
allocation fails on 64 bit architectures.
Additionally, the wcid mask array was too small in cases where the array
was not a multiple of BITS_PER_LONG.
Fix this by making the wcid mask array u32 instead and use DIV_ROUND_UP
for the size, just in case we ever bump it to a value that's not a multiple
of 32.
Signed-off-by: Felix Fietkau <[email protected]>
switch to per-vif ps support since mt7615 offload firmware can handle it
properly. This patch allows enabling/disabling power-save support on p2p
interface
Tested-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce remain_on_channel support to mt7615 driver if the device is
running offload firmware
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The newer 802.11ax devices (i.e. MT7915E) can connect to much more
peers than previous generations.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Tested on Chromebok by "echo mem to /sys/power/state" to suspend and
then waked up by keyboard keystrokes to resume system.
Signed-off-by: Sean Wang <[email protected]>
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce support for mt7663u 802.11ac 2x2:2 chipset to mt7615 driver.
Main difference respect to pcie code base is the usb code needs to
configure wtbl from non-atomic context
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce headroom and tailroom to mt76_mcu_ops data structure in order
to unify the routine used for mcu message allocation. This is a
preliminary patch to add mt7663u support
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt7615_mcu_send_message routine in order to allocate mcu skb
out of mcu sending routine. This approach is useful when the mcu
message is complicated and it is convenient to rely on skb buffer API
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
If a MCU timeout occurs before a hw restart completes, another hw restart
is scheduled, and the station state gets corrupted.
To speed up dealing with that, do not issue any MCU commands after the first
timeout, and defer handling timeouts until the reset has completed.
Also ignore errors in MCU commands during start/config to avoid making user
space fail on this condition. If it happens, another restart is scheduled
quickly, and that usually recovers the hardware properly.
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt76_mcu data structure to contain common fields between
mt76u_mcu and mt76e_mcu.
Initialize mcu common fields in mt76_alloc_device().
Rely on mt76_mcu in mt76_mcu_rx_event and in mt76_mcu_get_response
in order to reuse them in usb code
Signed-off-by: Lorenzo Bianconi <[email protected]>
Set RX scatter gather number to 4 in order to extend the maximum AMSDU
size to 11,454.
Signed-off-by: Sean Wang <[email protected]>
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Unify code converting between the different txpower values. Always add/remove
the combined txpower delta before dividing half-dB values.
Also fix the combined txpower delta values. The correct half-dB delta for
3 chains is 9, not 8.
Signed-off-by: Felix Fietkau <[email protected]>
