Enable hw rx-amsdu de-aggregation support available in 7915 devices.
This is a preliminary patch to enable rx checksum offload
Signed-off-by: Lorenzo Bianconi <[email protected]>
Only clear dev->phy2 after the phy is gone, the driver may still need to access
it until shutdown is complete
Signed-off-by: Felix Fietkau <[email protected]>
Add testmode support for DBDC NICs (both MT7615D and MT7915D work).
Testmode data and parameters are moved from per-dev to per-phy
for maintaining the value of each band.
Signed-off-by: Shayne Chen <[email protected]>
Acked-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to properly support mt7915 dbdc
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce dbdc support to mt7915 devices
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to properly support mt7915 dbdc
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to move properly support mt7915 dbdc
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move hw data queues in mt76_phy from mt76_dev since mt7915 supports per
phy hw queues in dbdc mode
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt76_init_mcu_queue utility routine in order to allocate
dedicate q_mcu pointers for mcu hw queues. This is a preliminary patch
to move data queues in mt76_phy and add dbdc support to mt7915 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_init_tx_queue in mac80211.c since it is shared by all
drivers.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
It was accidentally dropped while adding multiple wiphy support
Fixes fast-rx support and avoids handling reordering in both mac80211
and the driver
Cc: [email protected]
Fixes: c89d36254155 ("mt76: add function for allocating an extra wiphy")
Signed-off-by: Felix Fietkau <[email protected]>
The newer chipsets can deal with the same STA on multiple interfaces
Preparation for supporting more station interfaces
Signed-off-by: Felix Fietkau <[email protected]>
Introduce sdio tx aggregation to reduce bus transaction ands improve tx
throughput. For the moment the skb are copied in a dedicated buffer
since mmc APIs do not support sg table for zero-copy.
Since skb data are already copied in xmit_buff[], avoid linearization in
ma80211 layer. Relying on tx aggregation, we improve tx tpt of ~65%.
Tested-by: Sean Wang <[email protected]>
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
On MT7615 and MT7915, packets received from DMA can include TX_FREE events,
which free up space for tx. In order to process those packets faster, keep
keep a longer internal queue of packets and pass as many packets to the
stack as the NAPI budget allows
Signed-off-by: Felix Fietkau <[email protected]>
Since the switch to using AQL by default, mtxq->retry_q is never filled anymore
Remove it to get rid of a few more unnecessary cycles in the tx path
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt76_sdio module as common layer to add mt7663s support
Co-developed-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Introduce mt7615_update_survey utility routine in order to compute
survey stats without waking up the device since it runs holding mt76 lock.
Run mt7615_pm_wake directly in mt7615_update_channel since it can run
with mt76.mutex held if called by mac80211
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76 workqueue from usb to common code in order to be reused adding
low-power support for mt7663 chipset
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This can be used for calibration in the manufacturing process.
It supports sending a configurable number of packets with a specific rate
and configurable tx power levels / antenna settings.
It also supports receiving packets and showing some statistics, including
packet counters and detailed RSSI information.
It will only be compiled in if CONFIG_NL80211_TESTMODE is enabled
Signed-off-by: Felix Fietkau <[email protected]>
Introduce U-APSD support in mt76 driver for AP interface
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
While looking at the ETSI regulatory domain definitions
and a patch, which allows more channels for ath10k, I also
checked the channels allowed for mt76.
ETSI regulations would possibly allow to add channels 32, 68,
96, 144, 169 and 173. IEEE 802.11-2016 defines no operating class
for channels 32, 68 and 96. This leaves us channels 144, 169 and 173,
which are included in this patch.
I tested 169 and 173 with a mt76 based USB dongle (AVM AC 860) and they
worked fine. If I saw that right, these channels are also covered by
register definitions inside the driver.
Channel 144 should also work, but gets disabled by the kernel as of now.
Signed-off-by: Markus Theil <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Enable mac80211 TDLS support by default. Disable TDLS hw filtering for
mt7615 devices
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The hardware requirements for A-MPDU density are entirely on the tx side,
not the rx side. Because of that, the IE value should stay at 0 and the
minimum value should instead be enforced in WTBL/TXWI
MT7615 has no restrictions here
Signed-off-by: Felix Fietkau <[email protected]>
remove IEEE80211_HW_PS_NULLFUNC_STACK capability from mt76_phy_init
routine since 802.11 ps is not currently supported by any devices and it
will conflict with mt7663 ps fw support
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce mt76_mcu data structure to contain common fields between
mt76u_mcu and mt76e_mcu.
Initialize mcu common fields in mt76_alloc_device().
Rely on mt76_mcu in mt76_mcu_rx_event and in mt76_mcu_get_response
in order to reuse them in usb code
Signed-off-by: Lorenzo Bianconi <[email protected]>
The mt76_led_cleanup() function is called unconditionally, which
leads to a link error when CONFIG_LEDS is a loadable module or
disabled but mt76 is built-in:
drivers/net/wireless/mediatek/mt76/mac80211.o: In function `mt76_unregister_device':
mac80211.c:(.text+0x2ac): undefined reference to `led_classdev_unregister'
Use the same trick that is guarding the registration, using an
IS_ENABLED() check for the CONFIG_MT76_LEDS symbol that indicates
whether LEDs can be used or not.
Fixes: 36f7e2b2bb1d ("mt76: do not use devm API for led classdev")
Signed-off-by: Arnd Bergmann <[email protected]>
Acked-by: Felix Fietkau <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Unify code converting between the different txpower values. Always add/remove
the combined txpower delta before dividing half-dB values.
Also fix the combined txpower delta values. The correct half-dB delta for
3 chains is 9, not 8.
Signed-off-by: Felix Fietkau <[email protected]>
Move WIPHY_FLAG_HAS_CHANNEL_SWITCH in mt76-core module since now all
drivers support Channel Switch Announcement
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
