Remove obsoleted codes. This is the preparation for .set_bitrate_mask().
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
"idx" needs to be signed for the error handling to work.
Fixes: 495184ac91bb ("mt76: mt7915: add support for applying pre-calibration data")
Signed-off-by: Dan Carpenter <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Instead of attaching the last reported rate to tx packets, use
ieee80211_tx_status_ext to immediately pass the rate to mac80211 after
receiving it from the firmware.
Preparation for implementing full tx status reporting
Signed-off-by: Felix Fietkau <[email protected]>
In order to remove duplicated code, move mt76_token_init in
mt76_alloc_device routine
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Precision %.*s was intended instead of width %*s. The original code
will still print unintended data from beyond the end of skb->data.
Fixes: 665b2c780d63 ("mt76: mt7915: limit firmware log message printk to buffer length")
Signed-off-by: Dan Carpenter <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Do not read rf value from efuse when driver is configured to
use flash mode.
Tested-by: Bruce Chuang <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move token management in mt76 common module since it is shared between
mt7615, mt7915 and mt7921 drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move token_lock, token and token_count data structures in mt76_dev.
This is a preliminary patch to move token management in mt76 common
module since it is shared by mt7615, mt7915 and mt7921 drivers.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add the capability to define a custom rx napi callback for each driver.
This is a preliminary patch to properly support runtime-pm on rx side
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Junlin Yang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Since driver no longer handler per-rate tx power setting, we need to
read the power values directly from registers.
Tested-by: Evelyn Tsai <[email protected]>
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Clean up the flow of per-rate txpower limit setting to get rid of
duplicate work since it has already been handled by firmware, and set
proper max_power based on different channels and regdomains.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Dump mcu command code in hex and related prefix to help debugging
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When the EEPROM data is read from flash, it can contain pre-calibration
data, which can save calibration time.
Note that group_cal can save 30% bootup calibration time, and dpd_cal can
save 75% channel switching time.
Tested-by: Bo Jiao <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
After DMA reset, tx status information for queued frames will never arrive.
Flush the queue to free skbs immediately instead of waiting for a timeout
Signed-off-by: Felix Fietkau <[email protected]>
In mt7915_mac_reset_work(), make sure freeing skbs after mt7915_dma_reset().
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt7915_tx_token_put() should get call before mt76_free_pending_txwi().
Fixes: f285dfb98562 ("mt76: mt7915: reset token when mac_reset happens")
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Fix ofdm rate index and ldpc setting in rate setting field of tx
descriptor.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rework mt7915_tm_set_tx_len() with mt76_testmode_alloc_skb() to support
larger packet based on a longer tx_time.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add mmio.c in order to use mt76_bus_ops throughout the driver.
It will be also shared with the future APSoC revision.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Frame reception timestamp (low 32-bits) that indicates the value of the
local TSF timer value at the time the first bit of the MAC header in the
received frame (PPDU unit) arriving at the MAC.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Reset wifi subsystem when MCU is already running.
Fixes firmware download failure after soft reboot on systems where the PCIe
reset could not be performed properly.
Signed-off-by: Ryder Lee <[email protected]>
Co-developed-by: Felix Fietkau <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
ieee80211_beacon_get_template() returns NULL when beacon state is disabled.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
The same as mt7615. Keep BSS_INFO_BASIC enabled throughout interfaces
life cycle.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
When disassociating and clearing the BSSID of a repeater entry used by a client
mode interface, the corresponding MAC address entry can get lost too, causing
the client interface to not be able to associate anymore.
Fix this by also refreshing the MAC address when setting the BSSID
Signed-off-by: Felix Fietkau <[email protected]>
Deleting a key with the previous key index deletes the current key
Rework the code to better keep track of multiple keys and check for the
key index before deleting the current key
Signed-off-by: Felix Fietkau <[email protected]>
ieee80211_register_hw() is called with rtnl_lock held, and this could be
caused lockdep from a work item that's on a workqueue that is flushed
with the rtnl held.
Move mt7915_register_ext_phy() outside the init_work().
Signed-off-by: Evelyn Tsai <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Properly check returned values from mcu utility routines in
mt7915_ops.
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Avoid directly updating sinfo->rxrate from firmware since rate_info might
be overwritten by wrong results even mt7915_mcu_get_rx_rate() fails check.
Add more error handlings accordingly.
Fixes: 11553d88d0b9 ("mt76: mt7915: query station rx rate from firmware")
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In order to properly report MIB counters to mac80211, resets stats in
mt7915_get_stats routine() and hold mt76 mutex accessing MIB counters.
Sum up MIB counters in mt7915_mac_update_mib_stats routine.
Fixes: c6b002bcdf ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Similar to mt7921, fix 802.11 aggr len debugfs reporting for mt7915 driver.
Fixes: e57b7901469fc ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
