Driver core holds a reference to the USB interface and its parent USB
device while the interface is bound to a driver and there is no need to
take additional references unless the structures are needed after
disconnect.
Drop the redundant device reference to reduce cargo culting, make it
easier to spot drivers where an extra reference is needed, and reduce
the risk of memory leaks when drivers fail to release it.
Signed-off-by: Johan Hovold <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Felix Fietkau <[email protected]>
The interrupt status polling is unreliable, which can cause status events
to get lost. On all newer chips, txs-timeout is an indication that the
packet was either never sent, or never acked.
Fixes issues with inactivity polling.
Signed-off-by: Felix Fietkau <[email protected]>
This allows the core code to change the channel. Code deduplication and
preparation for adding scanning code to the core.
Signed-off-by: Felix Fietkau <[email protected]>
Introduce __mt76u_init unitility routine and move mt7615 usb bus ops
into mt7615 module in order to allow specifying driver specific
parameter.
This is a preliminary patch to add usb support to mt7921 driver.
Tested-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add SAR spec support to mt76x02 driver to allow configuring SAR power
limitations on the frequency ranges from the userland.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mac_work delayed_work and mac_work_count in mt76_phy since it is
used by all drivers. This is a preliminary patch to create a common mcu
library used by mt7615 and mt7921 drivers
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76 workqueue from usb to common code in order to be reused adding
low-power support for mt7663 chipset
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce extended utility routines to read/write data o usb bus. New
devices (e.g. mt7663u) will rely on both upper and lower part of the
register address. Add ext parameter to mt76u_init signature in order to
reuse the code adding mt7663u support.
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mcu buffer allocation in mt76x2u/mt76x0u drivers since newer
chipsets (e.g. mt7663u) does not rely on synchronous mcu communication
Co-developed-by: Sean Wang <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Starting from 'commit ee8040139ab1 ("mt76: do not overwrite
max_tx_fragments if it has been set")' we can avoid overwriting
max_tx_fragments for mt76x02u devices
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 655 file(s).
Signed-off-by: Thomas Gleixner <[email protected]>
Reviewed-by: Allison Randal <[email protected]>
Reviewed-by: Kate Stewart <[email protected]>
Reviewed-by: Richard Fontana <[email protected]>
Cc: [email protected]
Link: https://lkml.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
Move mt76_get_antenna in mac80211.c in order to be reused by all
drivers. Initialize .get_antenna function pointer for mt76x0, mt7603,
mt7615 and mt76x2u drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
rate controller and throughput are very sensitive to tx status timing.
In order to improve performances when the system is heavily loaded,
substitute stat_work delayed_work with a regular work_struct and create
a mt76u dedicated workqueue for tx status reporting
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
usb drivers are supposed to communicate using usb_interface instead
mt76x{0,2}u is now registering through usb_device. Fix it by passing
usb_intf device to mt76_alloc_device routine.
Fixes: 112f980ac8926 ("mt76usb: use usb_dev private data")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Tested-By: Zero_Chaos <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Report total rx airtime for valid stations as BSS rx time in survey
mt7615 is left out for now, it will be supported later by reading
hardware counters instead of calculating airtime in software
Signed-off-by: Felix Fietkau <[email protected]>
Unify mt76x02u_mac_start between mt76x2u and mt76x0u since the
code is shared between both drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce a default implementation for mt76_sw_scan and
mt76_sw_scan_complete in mt76 module and remove duplicated code
since most of the drivers share the same implementation
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce channel survey support for mt76x2u and mt76x0u drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This fixes the following checkpatch warnings:
ERROR: code indent should use tabs where possible
CHECK: Alignment should match open parenthesis
CHECK: No space is necessary after a cast
CHECK: Please don't use multiple blank lines
CHECK: Avoid precedence issues in macro
WARNING: Statements should start on a tabstop
WARNING: Unnecessary space before function pointer arguments
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Reduce rx memory footprint allocating just one SG buffer since for the
moment we support just 3839B as maximal size of an A-MSDU.
Introduce different SG_MAX_SIZE definitions for TX and RX sides.
Moreover set q->buf_size to PAGE_SIZE even for SG case.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mac80211 .start(), .stop() callbacks are never called concurrently with
other callbacks. The only concurencly is with mt76 works which we cancel
on stop() and schedule on start().
This fixes possible deadlock on cancel_delayed_work_sync(&dev->mac_work)
as mac_work also take mutex.
Signed-off-by: Stanislaw Gruszka <[email protected]>
On suspend mac80211 .stop callback is called before .suspend(), so
hw mac is already stopped and we do not have to do this again.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Move mac_work delayed work in mt76_dev data structure since
it is used by all drivers and it will be reused adding mac work to
mt7615
Signed-off-by: Lorenzo Bianconi <[email protected]>
Since some USB device IDs are duplicated between mt76x0u, mt7601u
and mt76x2u device, check chip version on probe and return error if
not match the driver.
Don't think this is serious issue, probe most likely will fail at
some other point for wrong device, but we do not have to configure
it if we know is not our device.
Reported-by: Xose Vazquez Perez <[email protected]>
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Setup usb device private data. This allows to remove mt76u_buf->dev
and simplify some routines as no longer we need to get usb device
through usb interface.
Signed-off-by: Stanislaw Gruszka <[email protected]>
All mt76 drivers (now also USB drivers) require empty .set_tim
callback. Add it to common mt76 module and use on all drivers.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Create software MT_TXQ_PSD queue for USB and map it to MT_TXQ_VO
since we do not have USB endpoint for PSD. This should make
mt76_release_buffered_frames() work by sending released frames
via MT_TXQ_VO.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add sta_ps callback but dont set WCID drop sicne registers for USB
can not be accessed from tasklet context.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add implementation of beacon_ops for USB and exit function to
stop the timer if running when device is removed. Still no
actual work on pre tbtt event.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move most of beaconing code into separate file and separate beacon
initialization for USB and MMIO as pre TBTT implementation for USB
will be different.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mutex->lock must not be held while cancelling workqueues, because it is held
by the workqueue items themselves
Signed-off-by: Felix Fietkau <[email protected]>
Use usb_bulk_msg for reading MCU command responses. This simplify code
a lot.
Together with 97a3005759c ("mt76usb: allow mt76u_bulk_msg be used
for reads") it also fix possible problems with rx data buffers
not being aligned and contained within single page. After doing
page_frag_alloc(1024) consecutive page_frag_alloc(PAGE_SIZE) will
alloc PAGE_SIZE buffer at PAGE_SIZE - 1024 offset.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
We need to reset MCU and do other initializations on resume otherwise
MT7610U device will fail to initialize, what cause system hung due to
USB requests timeouts.
Patch fixes 4.19 -> 4.20 regression.
Cc: [email protected] # 4.20+
Signed-off-by: Stanislaw Gruszka <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Move mt76u_check_sg routine in usb.c and introduce sg_en variable
in mt76_usb in order to check if scatter-gather is supported by
mt76u layer
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove mt76x0u_alloc_device since it just runs mt76_alloc_device.
Move mt76_alloc_device call in mt76x0u_probe and in mt76x0e_probe
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
ED/CCA Tx blocking checks need to be run every 100 ms in order to avoid
triggering too late and keeping tx blocking on for too long
Signed-off-by: Felix Fietkau <[email protected]>
