Currently, per-radio attributes are set on per-phy basis, i.e., all the
radios present in a wiphy will take attributes values sent from user. But
each radio in a wiphy can get different values from userspace based on
its requirement.
To extend support to set per-radio attributes, add support to get radio
index from userspace. Add an NL attribute - NL80211_ATTR_WIPHY_RADIO_INDEX,
to get user specified radio index for which attributes should be changed.
Pass this to individual drivers, so that the drivers can use this radio
index to change per-radio attributes when necessary. Currently, per-radio
attributes identified are:
NL80211_ATTR_WIPHY_TX_POWER_LEVEL
NL80211_ATTR_WIPHY_ANTENNA_TX
NL80211_ATTR_WIPHY_ANTENNA_RX
NL80211_ATTR_WIPHY_RETRY_SHORT
NL80211_ATTR_WIPHY_RETRY_LONG
NL80211_ATTR_WIPHY_FRAG_THRESHOLD
NL80211_ATTR_WIPHY_RTS_THRESHOLD
NL80211_ATTR_WIPHY_COVERAGE_CLASS
NL80211_ATTR_TXQ_LIMIT
NL80211_ATTR_TXQ_MEMORY_LIMIT
NL80211_ATTR_TXQ_QUANTUM
By default, the radio index is set to -1. This means the attribute should
be treated as a global configuration. If the user has not specified any
index, then the radio index passed to individual drivers would be -1. This
would indicate that the attribute applies to all radios in that wiphy.
Signed-off-by: Roopni Devanathan <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Johannes Berg <[email protected]>
This allows the core code to change the channel. Code deduplication and
preparation for adding scanning code to the core.
Signed-off-by: Felix Fietkau <[email protected]>
Add SAR spec support to mt76x02 driver to allow configuring SAR power
limitations on the frequency ranges from the userland.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 655 file(s).
Signed-off-by: Thomas Gleixner <[email protected]>
Reviewed-by: Allison Randal <[email protected]>
Reviewed-by: Kate Stewart <[email protected]>
Reviewed-by: Richard Fontana <[email protected]>
Cc: [email protected]
Link: https://lkml.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
Convert mt76_is_mmio and mt76_is_usb to rely on mt76_dev instead of
mt76x02_dev since this is a property not strictly related to hw chipset
and it will be more reusable
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Unify mt76x02u_mac_start between mt76x2u and mt76x0u since the
code is shared between both drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This fixes the following checkpatch warnings:
ERROR: code indent should use tabs where possible
CHECK: Alignment should match open parenthesis
CHECK: No space is necessary after a cast
CHECK: Please don't use multiple blank lines
CHECK: Avoid precedence issues in macro
WARNING: Statements should start on a tabstop
WARNING: Unnecessary space before function pointer arguments
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove mt76x0u_alloc_device since it just runs mt76_alloc_device.
Move mt76_alloc_device call in mt76x0u_probe and in mt76x0e_probe
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Unify drv_bss_info_changed mac80211 callback and remove duplicated
code in mt76x0 and mt76x2 drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76x02_set_rts_threshold and mt76x02_mac_set_tx_protection
routines in mt76x02-lib module and remove duplicated code in mt76x0
and mt76x2 drivers. Remove pci_mac.c and mt76x0/mac.c since now are
empty files
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add missing mac80211 callbacks to mt76x0e_ops data structure
and add mt76x02_beacon utility routines in mt76x0_bss_info_changed
in order to enable/disable beacon transmission
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76x02_sw_scan and mt76x02_sw_scan_complete utility routines
in mt76x02_util.c in order to be reused by mt76x0 and mt76x2u drivers
and remove duplicated code
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76x02_mac_set_short_preamble routine in mt76x02-lib module
since it is shared between mt76x0 and mt76x2 drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Unify firmware version used on mt76x0e and mt76x0u drivers.
Fallback to mt7610u fw if mt7610e one is not available
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove no longer used mt76x0_mac_set_ampdu_factor routine
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Some RF registers need different values for various chips.
For at least mt76x0_rf_central_tab registers, overwriting them later does
not work, as the wrong values can cause the entire system to hang on some
devices with MT7610E
Signed-off-by: Felix Fietkau <[email protected]>
Driver works better for MT7630 without MCU calibration, which
looks like it can hangs the firmware. Vendor driver do not
perform it for MT7630 as well.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Align phy calibration logic between mt76x0u and mt76x0e drivers
This patch improves connection stability with low SNR
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use mt76x02_mac_work utility routine as stats workqueue handler
and remove duplicated code. Moreover run mac stuck check in
mt76x02_mac_work for client interfaces.
Remove no longer used avg_ampdu_len and mt76x02_mac_stats data
structure in mt76x02_dev
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use mt76x02 debugfs implementation and remove duplicated code
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76x02_mac_work routine in mt76x02_mac.c in order to be reused by
mt76x0 driver to read device statistics
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use mt76x0_phy as prefix for routines in mt76x0/phy.c
Moreover use mt76x0_rf_set to enable vco calibration in
mt76x0_phy_vco_cal
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Do not perform phy/vga calibration during channel switch.
Moreover remove mt76x0_agc_save and mt76x0_agc_restore routines
since they are no longer necessary. Furthermore run mt76_set_channel
in order to check if there are pending frames during channel switch
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add mt76x0_phy_calirate routine in order to perform
phy calibration for mt76x0e devices.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rename mt76x02_util.h header file in mt76x02.h since now contains
all mt76x02 related definitions and not just utility routines
declarations
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76x02_tx shared routine in mt76x02-lib module and remove
duplicated code. Moreover remove mt76x0/tx.c since it is an empty
file
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Unify rxwi parsing between mt76x2 and mt76x0. Remove the following
routines:
- mt76x0_phy_get_rssi
- mt76x0_queue_rx_skb
- mt76x0_mac_process_rx
Moreover remove mt76x2/common.c and mt76x0/mac.h since are empty files
Enable CCMP PN sw validation
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Merge mt76x0_dev data structure in mt76x02_dev one and remove
duplicated code. Remove unused definition in mt76x0.h.
Moreover merge mt76x0_caldata and mt76x02_rx_freq_cal data structures.
This is a preliminary patch for rxwi unification.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove hw_atomic_mutex mutex in mt76x0_dev data structure
since mt76x0_phy_set_channel is already protected by mt76_dev
mutex while mt76x0_chip_onoff is used just at device probe or
cleanup
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove no longer used mac_lock spinlock and data array
in mt76x0_dev data structure
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use shared mt76x02 utility routines for rssi tracking.
Moreover remove no longer used con_mon_lock spinlock
and following variable:
- ap_bssid
- bcn_freq_off
- bcn_phy_mode
- avg_rssi
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use mt76x02u_tx_prepare_skb routine to fill txwi in mt76x2u and
mt76x0u driver and remove duplicated code. Moreover add static
qualifier to mt76x02_mac_tx_rate_val and mt76x02_mac_fill_txwi
routines
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76x0u_tx_prepare_skb routine in usb module in
order to remove leftover usb dependency from generic code
Signed-off-by: Lorenzo Bianconi <[email protected]>
Add ieee80211_ops ops pointer to mt76x0_alloc_device routine signature
in order to specify mac80211 callbacks and remove usb dependency from
mt76x0 generic code.
Move mt76x0_ops callbacks in usb module in order to remove leftover
usb dependency in mt76x0 generic code.
Introduce mt76x0e_ops mac80211 callbacks for pci code
Signed-off-by: Lorenzo Bianconi <[email protected]>
Move mt76x02_phy_set_rxpath and mt76x02_phy_tx_dac routines in
mt76x02_phy.c since they are shared between mt76x2 and mt76x0 drivers.
Moreover move chainmask variable from mt76x2/mt76x0 to mt76_dev data
structure
Signed-off-by: Lorenzo Bianconi <[email protected]>
Move usb initialization code in mt76x0-usb module in
order to remove usb dependency from generic init code
(not completed yet). Moreover fix a memory leak in usb probe
if mt76x02_wait_for_mac fails
Signed-off-by: Lorenzo Bianconi <[email protected]>
Move mt76x02_beacon_offset utility routine in mt76x02-lib module
since it is shared between mt76x0 and mt76x2 driver and remove
duplicated code. Moreover move beacon_offset data structure in
mt76x02-lib module since it is shared between mt76x0 and mt76x2
drivers
Signed-off-by: Lorenzo Bianconi <[email protected]>
TP-LINK Archer T1U do not support 2.4GHz band despite EEPROM
reports that. Add quirk to mask out 2.4GHz support.
Reported-by: Sid Hayn <[email protected]>
Signed-off-by: Stanislaw Gruszka <[email protected]>
Add mt76x0_phy_set_txpower routine in order to configure
base and per rate tx power gain. Moreover take into account
txpower_conf in order to limit the tx power gain according to
the bound provided by mac80211
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Use mt76 shared debugfs implementation and remove duplicated code
in mt76x0 driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In order to unify eeprom parsing between mt76x0 and mt76x2 drivers,
remove eeprom pointer dependency from mt76x0_get_power_info routine.
Remove mt76x0_eeprom_params since it is now an empty structure
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Unify lna gain parsing with mt76x2 driver using eeprom utility
routines available in mt76x02-lib module
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
We don't need to use custom burst write regs via MCU, we can use
generic mt76_wr_copy() for the same purpose.
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Add USB implementation for read and write reg pair routines.
The actual implementation can use mcu related routines according to
MCU state
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Use mt76_register_device routine for device registration.
mt76_register_device allows to enable VHT support on 5GHz band.
Overwrite unsupported vht features with mt76x0_vht_cap_mask routine.
Remove macaddr field of mt76x0_dev data structure and
use the mt76_dev one. Moreover remove following unused routines:
- mt76_init_sband
- mt76_init_sband_2g
- mt76_init_sband_5g
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Stanislaw Gruszka <[email protected]>
