Country Location Control (CLC) is an additional control for country rules
in firmware. We introduce this new feature to make sure mt7921 series
working properly in all region.
The addtional policies would be put into firmware based on differnt
regions. mt76 driver should be in charge of submitting per region policy.
Reviewed-by: Sean Wang <[email protected]>
Tested-by: YN Chen <[email protected]>
Co-developed-by: Deren Wu <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Since both mt7921_rx_check and mt7921_queue_rx_skb routines are used by
all chipsets (mmio, usb and sdio), move them in mac.c and remove
duplicated code.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Introduce rx_check callback support for mt7663u and mt7921u drivers.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_connac_init_tx_queues and mt76_connac_tx_cleanup routines
in mt76_connac module. This is a preliminary patch to add mt7990
chipset support.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt7921_pci_driver struct is only referenced in mt7921/pci.c so make it
static.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_connac2_mcu_fill_message routine in shared module in order to
reuse it for mt7921 and mt7915e drivers. This is a preliminary patch to
add mt7990 driver support.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Since now txp structures are in common code we can reuse
mt76_connac_tx_complete_skb routine in mt7921e, mt7915e and mt7615e
drivers.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Due to AP stop improperly, mt7921 driver would face random command timeout
by chip fw problem. Migrate AP start/stop process to .start_ap/.stop_ap and
congiure BSS network settings in both hooks.
The new flow is shown below.
* AP start
.start_ap()
configure BSS network resource
set BSS to connected state
.bss_info_changed()
enable fw beacon offload
* AP stop
.bss_info_changed()
disable fw beacon offload (skip this command)
.stop_ap()
set BSS to disconnected state (beacon offload disabled automatically)
destroy BSS network resource
Fixes: 116c69603b01 ("mt76: mt7921: Add AP mode support")
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mac_write_txwi code is shared between connac2 devices (mt7915 and
mt7921). Move it in connac module.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to share connac2 mac txwi code.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to share txwi configuration code.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add new function mt7921_set_tx_sar_pwr() to update SAR power from
.set_sar_specs and ACPI setting. Both settings would be merged into
mt76_freq_range_power for final tx power value.
Reviewed-by: Sean Wang <[email protected]>
Co-developed-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In ACPI SAR enabled device, mt7921 should read power limit in ACPI config.
The limit value would be applied to regular tx power settings in mt76.
Two major functionalities added:
1. Get SAR power table through ACPI.
2. Read power in Dynamic/Geo SAR table for tx power limit.
Table note
MTDS: Dynamic SAR table
MTGS: Geo SAR table
MTCL: Country List table (for 6GHz support)
Reviewed-by: Sean Wang <[email protected]>
Co-developed-by: Quan Zhou <[email protected]>
Signed-off-by: Quan Zhou <[email protected]>
Co-developed-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add ipv6 NS offload for WoWLAN state.
Tested in this way:
1. Put device-A into WoW state.
2. ping6 from device-B to device-A.
3. In sniffer, see Neighbour advertisement from device-A.
Reviewed-by: Sean Wang <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Ming Yen Hsieh <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt7921 is currently using rxfilter defined in mt76_dev for rx filter
configuration. Fix mt7921_configure_filter implementation.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Firmware initialization can take a while. Move mt7921_init_hw routine in
a dedicated work in order to not slow down bootstrap process.
Tested-by: Deren Wu <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Properly set up the monitor mode the firmware can support to fix up
RTS/CTS and beacon frames cannot be captured and forwarded to the host.
Tested-by: Deren Wu <[email protected]>
Tested-by: Sven Eckelmann <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt76_connac_lmac_mapping is shared between mt7921 and mt7915
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Toggle runtime-pm and deep-sleep configuration adding/removing
a montior vif in order to forward all tx/rx frames to mac80211.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Tested-by: Sven Eckelmann <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
It doesn't guarantee the mt7921e gets started with ASPM L0 after each
machine reboot on every platform.
If mt7921e gets started with not ASPM L0, it would be possible that the
driver encounters time to time failure in mt7921_pci_probe, like a
weird chip identifier is read
[ 215.514503] mt7921e 0000:05:00.0: ASIC revision: feed0000
[ 216.604741] mt7921e: probe of 0000:05:00.0 failed with error -110
or failing to init hardware because the driver is not allowed to access the
register until the device is in ASPM L0 state. So, we call
__mt7921e_mcu_drv_pmctrl in early mt7921_pci_probe to force the device
to bring back to the L0 state for we can safely access registers in any
case.
In the patch, we move all functions from dma.c to pci.c and register mt76
bus operation earilier, that is the __mt7921e_mcu_drv_pmctrl depends on.
Fixes: bf3747ae2e25 ("mt76: mt7921: enable aspm by default")
Reported-by: Kai-Chuan Hsieh <[email protected]>
Co-developed-by: Deren Wu <[email protected]>
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Similar to mt7915 driver, process txfree and txstatus without allocating
skbs in order to reduce pressure on the memory allocator
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_connac_mcu_restart routine in mt76-connac since it is shared
between mt7921 and mt7915.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Remove mt7921_mcu_get_eeprom since it is no longer used.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move key configuration code shared between mt7921 and mt7915 in
mt76-connac module and remove duplicated code.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
TXS in mt7921 may be forwared to tx_done event. Should try to catch
TXS information in tx_done event as well.
Signed-off-by: Deren Wu <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
There is a missing mt7921e_driver_own in the MT7921E reset procedure
since the mt7921 mcu.c has been refactored for MT7921S, that will
result in MT7921E reset failure, so add it back now.
Fixes: dfc7743de1eb ("mt76: mt7921: refactor mcu.c to be bus independent")
Reported-by: YN Chen <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move tx_amsdu histogram stats in mib_stats structure since registers are
clear-on-read
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to add ethtool stats to mt7921 driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce ethtool stats support to mt7921
driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce mt7921s support.
Refactor mt7921_mcu_send_message to be sharable between mt7921s and
mt7921e.
Tested-by: Deren Wu <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rely on mcu_get_nic_capability to obtain Tx quota information
for the SDIO device, get PHY capability, MAC address and then we can
totally drop mt7921/eeprom.c and any unnecessary code.
Noting that mt76_connac_mcu_get_nic_capability should be run before set
flag MT76_STATE_MCU_RUNNING being set to setup the proper parameters
like Tx quota control before the device is started to running.
Tested-by: Deren Wu <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce mt7921s support.
Make init.c reusable between mt7921s and mt7921e
Tested-by: Deren Wu <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce mt7921s support.
Make mcu.c reusable between mt7921s and mt7921e
Tested-by: Deren Wu <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce mt7921s support.
make dma.c be used dedicately for mt7921e.
by moving out mt7921_tx_cleanup from dma.c to mcu.c and then renaming
mt7921_tx_cleanup to refect the exact thing the function actually does.
Finally, dma.c totally become pcie specific one, only needed to
be compiled only when CONFIG_MT7921E is enabled.
Tested-by: Deren Wu <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
This is a preliminary patch to introduce mt7921s support.
Split out a new pci_mac.c from mac.c to make mac.c reusable between
mt7921s and mt7921e.
Tested-by: Deren Wu <[email protected]>
Acked-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Unlock 6GHz band if supported by the device. Configure HE 6G
capabilities.
Tested-by: Deren Wu <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
