The hardware reports the number of transmitting antennas not the actual
number of spatial streams
Co-developed-by: Peter Chiu <[email protected]>
Signed-off-by: Peter Chiu <[email protected]>
Signed-off-by: Evelyn Tsai <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Add mt76_connac_spe_idx() for antenna mask to spatial extension
index conversion. This is used to support flexible control of
tx antenna.
Signed-off-by: Shayne Chen <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Given that there's no data coming from network stack for binding flows,
hence driver counts and reports station's statistics directly through
NL80211_STA_INFO_* based on active PPDU based TxS for offloading data.
Apart from that, WA firmware and its offloading engine (SDO) have hardcoded
"2" as PID, so we introduce MT_PACKET_ID_WED to differentiate WED reporting.
Note that PPDU format TxS is mutually exclusive with MT_TXD5_TX_STATUS_HOST.
Co-developed-by: Yi-Chia Hsieh <[email protected]>
Signed-off-by: Yi-Chia Hsieh <[email protected]>
Signed-off-by: Ryder Lee <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Report phy_indx in tx_info->hw_queue. This is a preliminary patch to add
newer chipset support
Co-developed-by: Bo Jiao <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Introduce phy_idx to mt76_wcid structure instead of ext_phy.
This is a preliminary patch to add newer chipset support.
Co-developed-by: Bo Jiao <[email protected]>
Signed-off-by: Bo Jiao <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Introduce phys array in mt76_dev structure to reference mt76_phy
supported by the chipset. This is a preliminary patch to introduce
newer chipset support.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Move mt76_connac_init_tx_queues and mt76_connac_tx_cleanup routines
in mt76_connac module. This is a preliminary patch to add mt7990
chipset support.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Previously the code used skb_set_queue_mapping for management or non-bufferable
powersave frames that need to be sent to a different hardware queue.
This can confuse AQL, which expects the value to remain the same until the tx
status report.
The only place that currently uses the altered skb queue mapping is the txwi
write function. Change the code to pass the hardware queue id as a function
parameter instead.
Signed-off-by: Felix Fietkau <[email protected]>
Move mt7615_txp_skb_unmap in shared code and reuse it in mt7915e and
mt7921e driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Now we can move mt76_connac_write_hw_txp routine in mt76-connac module
and reuse it in mt7921e and mt7615e driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Since now txp structures are in common code we can reuse
mt76_connac_tx_complete_skb routine in mt7921e, mt7915e and mt7615e
drivers.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Rely on mt76_connac2_mac_fill_rx_rate routine in mt7921 driver.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt76_connac2_reverse_frag0_hdr_trans routine is shared between mt7921
and mt7915e drivers.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
HE radiotap parsing code is shared between connac2 devices.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move mt76_connac2_mac_add_txs_skb in mt76-connac module since it is
shared between connac2 devices (mt7921 and mt7915)
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mac_write_txwi code is shared between connac2 devices (mt7915 and
mt7921). Move it in connac module.
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Allow the user to enable runtime-pm for mt7663s driver
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
mt7921_stop should put device in fw_own state to reduce
power consumption.
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In order to wake the device less frequently and so reduce power
consumpation, unschedule mac_work before going to sleep
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Simplify the code using a wait_queue_head_t instead of a completion to
wait the chip is fully awake in mt76_connac_pm_wake routine
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
move scanning check from mt76_connac_power_save_sched routine
to mt7921_pm_power_save_work/mt7615_pm_power_save_work ones
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
In order to avoid synchronization issues between wake and ps works,
cancel ps_work in mt76_connac_pm_wake routine
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
Move power_save common code shared between mt7663 and mt7921 in
mt76_connac module
Signed-off-by: Lorenzo Bianconi <[email protected]>
Signed-off-by: Felix Fietkau <[email protected]>
